background image

Rotary switch

 

A

A

 167 

 184 

 55.50 

SECTION A-A

Client:

Rev. nr:

1:1

Units:

1/2

CES-01 - Enclosure

MH

Vol. (mm³):

mm

Sheet:

Scale:

-

Cohere

Date:

Drawn:

File reference:

Drawing name:

-

Material:

17-02-2016

Maxem 4 Assembly

A3

Stereo Design | Zamenhofstraat 150 - unit 336 | 1022AG | Amsterdam | Netherlands | T: +31 (0) 20 636 0671 | M: [email protected]

<0,2x45° or R<0,2

Ra  0,8 um

Default length tolerances: DIN 7168

±20'

Default angle tol.:

Finish:

Default edges:

Roughness:

Tol.:    ±0,1    ±0,2     ±0,3         ±0,5           ±0,8

Dim.:    0-6     7-30   31-120    121-400    401-1000

Set the Wall Connector as Slave by placing the rotary switch in F position. 

Crimp the supplied RJ10 4P4C connector on Maxem side on the data cable. Two wires 
must be connected:
• 

Connect wire 1 (orange-white) to Pin 1

• 

Connect wire 2 (orange) to Pin 2

Connect the RJ10 4P4C connector to RS2 Maxem port. 

Connect the data cable to the IN (D+ and D-) port of the Wall Connector 
clamp block:
• 

Connect the wire from pin 1 on D+

• 

Connect the wire from pin 2 to D-

RS2 port for 

Tesla Wall Connector

LED indications Tesla Wall Connector

RS2

Pin 1

Pin 2

LED above lights up in green: everything is connected properly

Middle LED is blinking red: set as Slave but no connection with Maxem

Lower LED burns 5 secs. green: correctly set as Slave at start

RJ10 4P4C

See installation manual Tesla Wall Connector for more information

Tab above

Option 4.3 - Connecting Tesla Wall Connector 

Install a circuit breaker or earth leakage circuit breaker for each charging 
station at the maximal power available.

 See p. 10.

Follow the installation instructions of the charging station. These 
instructions  can  be  found  in  the  installation  manual  of  the  charging 
station.

Place a suitable UTP (CAT5 or CAT6) of the Wall Connector to Maxem. (To prevent 
electromagnetic interference at the RS485 connection, it is recommended to use FTP 
CAT6 cable at distance more than 25 m. Max: 50m).

SET

OK

1  2  3

Connect the RS485 cable to the kWh-meter as follows: 
• 

Port C: Green core

• 

Port B: White core

• 

Port A: Brown core

Place the kW-meter on a DIN rail in the installation cabinet.

Distribution board

Chargin station

Direction of current

Connect it in such a way that it measures the consumption of the charging station.

Connection  of RS485 cable
to kWh-meter

Set the addressing of the kWh-meter to 002. As a result, Maxem can configure itself. 

See Annex 2 how to set the addressing.

18

19

A.

B.

C.

D.

E.

F.

J.

I.

H.

G.

L.

Tesla Wall Connector does not measure kWh itself, therefore a MID 
kWh-meter is needed. 

Cores for pull relief

Connect the RS485 cable to RS1 port on Maxem.

A

A

 167 

 184 

 55.50 

SECTION A-A

Client:

Rev. nr:

1:1

Units:

1/2

CES-01 - Enclosure

MH

Vol. (mm³):

mm

Sheet:

Scale:

-

Cohere

Date:

Drawn:

File reference:

Drawing name:

-

Material:

17-02-2016

Maxem 4 Assembly

A3

Stereo Design | Zamenhofstraat 150 - unit 336 | 1022AG | Amsterdam | Netherlands | T: +31 (0) 20 636 0671 | M: [email protected]

<0,2x45° or R<0,2

Ra  0,8 um

Default length tolerances: DIN 7168

±20'

Default angle tol.:

Finish:

Default edges:

Roughness:

Tol.:    ±0,1    ±0,2     ±0,3         ±0,5           ±0,8

Dim.:    0-6     7-30   31-120    121-400    401-1000

RS1

D.

RS1 port for 

MID kWh-meter

Summary of Contents for maxem


















Reviews: