Cognex COV-7000-CMNT Reference Manual Download Page 32

Page: 32 / 84

6. Install the light housing.

CAUTION

Do not hot-plug the LED ring light. Verify the vision system is not receiving power when connecting

or disconnecting the LED ring light.

A connector protrudes from the underside of the light housing. To prevent damage, it is

recommended the light housing not be removed from the box until ready to be assembled.

Note

: If a different LED color is required, refer to

Replace the LED Ring Light (Optional)

on page 44

a. Place the light housing with LED ring light on top of the spacer, with “TOP” oriented upward.

b. Verify seating of the gasket on the top of the spacer.

c. There are four captive screw access holes near the white circles on the LED ring light. Use a 2mm hex

wrench to torque the captive screws to 0.34 Nm (3 in-lb).

Installation

Summary of Contents for COV-7000-CMNT





















































































Search results

Summary of Contents for COV-7000-CMNT

Reviews:

Related manuals for COV-7000-CMNT

Brands by name

Popular brands

Cognex COV-7000-CMNT, Reference Manual

Search results

Summary of Contents for COV-7000-CMNT

Reviews:

Related manuals for COV-7000-CMNT

Brands by name

Popular brands