background image

4

2.  18 PIN HARNESS

Hood Pin Input (-) (GRAY)

Install the supplied Hood Pin Switch and connect to the GRAY wire. This connection is required for
Remote Start.

Verification: This wire when connected will register ground when the vehicle's hood is opened.

Connect the GRAY wire to the hood pin.

NOTE: Be sure to loom the wire, and seal the grommet.

Ground When Armed Output (-) 300mA (ORANGE)

This wire will show Ground when the system is Armed. This wire is used for controlling window modules or

additional sensors.

Brake Input/Shutdown (+) (BROWN/RED)

Locate the vehicle’s brake light wire at the brake pedal mounted switch.

Verification:

 This wire registers positive voltage when the brake pedal is pressed.

Connect the BROWN/RED wire to the vehicle’s brake light wire.

Chassis  Ground Source (BLACK)

Connect the BLACK wire to a solid chassis ground point using a ring terminal and self tapping screw

(not supplied). Scrape away paint from the grounding point to ensure a good connection.  The
recommended grounding point is a metal surface in the driver’s side kick panel area.

NOTE: Do not ground the BLACK wire with any other vehicle components.

Door Trigger (+) (PURPLE)

Locate the vehicle’s dome light or door pin switch wire.

Verification: This wire will register positive voltage when the door is opened and the interior light is on.
This wire will register ground or "0" Volts when the door is closed and the interior light is off.

Connect the PURPLE wire to the vehicle’s positive door input wire(s).

NOTE: Certain vehicles may require multiple connections. Refer to 

Vehicle Wire Color and Location

Chart

 for wire color and location.

Door Trigger (-) (GREEN)

Locate the vehicle’s dome light or door pin switch wire.

Verification: This wire will register ground when the door is opened and the interior light is on.  This
wire will register positive voltage when the door is closed and the interior light is off.

Connect the GREEN wire to the vehicle’s negative door input wire(s).

NOTE: Certain vehicles may require multiple connections. Refer to 

Vehicle Wire Color and Location

Chart

 for wire color and location.

Summary of Contents for CA611






















Reviews: