background image

  

ACM-300 BUILT-IN DIMMER/SWITCH 

 

10

  The dimmer is exclusively intended for devices that are suitable for dimming. Connecting incorrect 

equipment can cause defects, a short circuit and fire. 

  The dimmer is suitable for the connection of 12 Volt halogen lighting with an electronic transformer as 

long as the lighting is suitable for connection to a dimmer. If the transformer hums, this means that it is 

not suitable for use with the COCO dimmer. If in doubt, consult your lighting supplier or installer. 

  This product is protected with a 20 mm fuse rated at 1.6 A (T1.6A, H250V). An equivalent fuse must be 

used during replacement. 

  Do not expose this product to excessive heat, direct sunlight or moisture. 

  Do not attempt to repair this product. If the product is damaged or if you are in doubt about the proper 

operation, take the product back to the place of purchase. 

  Do not use the product in damp areas. Clean the device with a clean cloth. 

 

  

Wireless 

  This product works using a radio signal that passes through walls, windows and doors. The range is 

maximum 75 metres in the open air. The range indoors is strongly influenced by local conditions such 

as concrete, glass and metals. On average, the indoor range is approximately 30 metres. 

  New double glass often includes a thin metallic layer. This type of glazing (“

HR glass

”) allows most 

visible light to pass through but has a negative impact on radio signals. If there is HR glass between the 

transmitter and receiver, you should expect a significant reduction of the range of the wireless signal. 

  This product operates at a frequency of 433.92 MHz. It complies with the essential requirements and 

other conditions of R&TTE Directive 1999/5/EC and can be used in all EU countries. 

  There may be restrictions on the use of this device outside the EU. If this device is used outside the EU, 

check whether the device complies with the local directives. 

 

 

This product complies with the essential requirements and other relevant provisions of the applicable 

European directives. The Declaration of Conformity (DoC) is available at www.coco-technology.com. 

 

 

 

If possible, submit this product for recycling after use. Do not dispose of the product with household trash. 

Summary of Contents for ACM-300














Reviews: