background image

 

ACM-300 BUILT-IN DIMMER/SWITCH 

Remarks 

 

  

Reminders 

  This product is intended for installation in a wall or ceiling junction box and must be used in combination 

with at least one COCO transmitter. 

  This product is a dimmer/receiver: control lights (or other suitable devices) remotely, without 

complicated wiring. 

  To prevent interference, avoid placing multiple products close to each other. The minimum distance 

between units should be approx. 50 cm. 

  The wireless system can be expanded indefinitely with other COCO remote controls and/or receivers. 

  Your COCO transmitter may have a special "group" button with which multiple receivers with different 

settings can nonetheless be controlled simultaneously. Repeat 

[8 - 10]

 and press the "group" button on 

the transmitter during step 

[9]

  During a power failure the codes remain in the memory. 

  To delete the stored codes (resetting the memory): (1) Hold in the search mode button. (2) The 

indicator begins flashing after approx. 7 seconds. (3) Release the search mode button. (4) Briefly press 

the search mode button again. (5) To confirm, the connected device switches on and off two times. 

  If the product does not work: 

- Reset the memory (see previous line) and set the code from the transmitter again (repeat 

[8 - 10]

). 

- Check whether the indicator is lit; if not, there may be no power to the product or the fuse may have 

blown. 

- Fuse replacement: (1) Open the wall or ceiling junction box. (2) Pry open the fuse holder with a 

screwdriver. (3) Press the fuse out of the holder (the fuse will be slightly blackened if it is blown). (4) 

Press the new fuse into the holder. (5) Press the holder into the dimmer and close the wall or ceiling 

junction box. 

 

  

Safety instructions 

  Do not connect any lights or other equipment that consume a total of less than 40 Watts or more than 

300 Watts. 

Summary of Contents for ACM-300














Reviews: