background image

7

Cobra Combi & Standard

© 2005 Atlas Copco Construction Tools AB 

|

 No 9800 0636 90 

|

 2005-09-16

Safety and operating instructions

Explosion and fire hazard, 
continued

 Warning

Fuel is highly flammable, and its vapors can 
explode if ignited, which can cause serious injury 
or death. To reduce risk of fire or explosion:

Store fuel only in containers that are specifically 
designed and approved for storage of fuel. 
Empty fuel containers must be properly taken 
care of and sent back to the retailer.

Operate the machine with the fuel cap securely 
in place. Never remove the fuel cap or add fuel 
when the engine is hot. Stop the engine and 
allow it to cool before adding fuel. When opening 
the fuel cap, always loosen the cap slowly to 
relieve any pressure in the tank. Do not overfill 
the tank.

Always mix and add fuel in a clean and well-
ventilated area. Make sure that this outdoor area 
is free from any flames or sparks. Never smoke 
while fuelling, mixing fuel, operating or servicing 
the machine. Avoid spilling fuel. Wipe up any 
fuel that is spilled on the machine. Fill the tank 
at least ten meters (30 feet) away from where 
you intend to use the machine. 

Do not use a machine that is leaking fuel.
Regularly check for any leakage.

To minimize the risk of fuel leakage during 
transportation, secure that the machine is in an 
upright position during transportation.

Do not use the machine near flammable 
materials, fumes or dust. During breaks in 
work, do not place the machine near flammable 
materials.

Do not operate the machine near any materials 
that create sparks. Remove all hot objects 
and objects that create sparks prior to using 
machine.

Do not operate the machine in an explosive 
environment.

Protect your skin from contact with fuel.

Electrical/Concealed object 
hazards

 Warning

The machine is not electrically insulated. If the 
machine comes in contact with electricity, serious 
injuries or death may result.  

To reduce the risk of injury or death, never drill 
or break near any electric wire or other source of 
electricity.  

Make sure that there are no concealed wires or 
other sources of electricity.  

 Warning

During drilling and breaking, concealed wires and 
pipes constitute a danger that can result in serious 
injury. 

Before you start drilling or breaking, check the 
composition of the material you are to work on.

 Watch out for concealed electrical wiring, water, 
sewage and gas pipes and phone lines. 

If the tool seems to have hit a concealed object, 
immediately switch off the machine. 

Make sure that there is no danger before 
continuing. 

Projectile hazard

 Warning

During breaking, drilling or hammering, splinters or 
other particles of rock may become projectiles and 
cause bodily injury by striking the operator or other 
persons.

Use approved personal protective equipment, 
including impact resistant safety glasses with 
side protection, to reduce the risk of being 
injured by a projectile.

Summary of Contents for Combi

















Reviews: