Cobra 25 LTD ST Installation Instructions Manual Download Page 3 | Manualshive

Page: 3 / 11

background image

The CB/PA button should be in the
CB position.

Operation

Operation

Turning On

Setting Channel
Selector

Turning On

Make sure the power cord, antenna and micro-
phone are connected to their proper connectors
before starting.

Setting Channel Selector

2

1

Rotate the On/Off Volume knob

clockwise

to

a normal listening level.

Select

one of forty channels and adjust

volume. The selected channel is indicated by
the LED readout directly above the channel
selector knob

1

«
1
2
3
4
5
...
»

Summary of Contents for 25 LTD ST












Reviews:

No comments

Related manuals for 25 LTD ST

Brand: Datron Pages: 82

Brand: La Crosse Technology Pages: 3

Brand: La Crosse Technology Pages: 2

Brand: La Crosse Technology Pages: 4

Brand: La Crosse Pages: 4

Brand: Dual Pages: 24

Brand: ICP DAS USA Pages: 28

Brand: Hyundai Pages: 24

Brand: Sangean Pages: 18

Brand: Living & Co Pages: 8

Brand: E.F. Johnson Pages: 69

Brand: CUSHCRAFT Pages: 12

Brand: Maximum Pages: 8

Brand: Richter Pages: 12

65 11 0 406 351

Brand: Sirius Satellite Radio Pages: 8

Brand: Uniden Pages: 4

Brand: Icom Pages: 6

Brand: Caliber Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands