Cobra 25 LTD ST Installation Instructions Manual Download Page 4 | Manualshive

Page: 4 / 11

background image

Rotate the On/Off Volume knob

clockwise

the green RT/TX LED and channel display will
be illuminated.

Operation

Operation

S-Meter

S-Meter

Swings proportionately to strength of incoming
signal when receiving.

Switch

to NORMAL to select desired channel.

1

Selecting A
Channel

Selecting A Channel

Note

Switch to 9 (Emergency) for
instant access to these channel.

To Receive

1

To Receive

«
...
2
3
4
5
6
...
»

Summary of Contents for 25 LTD ST












Reviews:

No comments

Related manuals for 25 LTD ST

Brand: Handic Pages: 59

Brand: Garmin Pages: 2

Brand: Garmin Pages: 11

Brand: iHome Pages: 2

Brand: iHome Pages: 16

Brand: La Crosse Technology Pages: 3

Brand: La Crosse Technology Pages: 2

Brand: La Crosse Technology Pages: 4

Brand: La Crosse Pages: 4

Brand: Marquant Pages: 12

Brand: Ericsson Pages: 16

BELT-PAK 5 Series

Brand: EARMARK Pages: 2

Brand: Vitek Pages: 6

Brand: SpotterRF Pages: 2

Brand: Aim Pages: 12

Brand: RACOM Pages: 157

Brand: Sunwave Pages: 47

Brand: Sytech Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands