background image

20

www.cobham.com/patriot

15.  Assemble the Drive motors to the Elevation acutator and the Azimuth Gearbox.

Mototized Mount Option  Assembly

Appendix  C

(continued)

Recommended Maintenance Schedule

Maintenance Item

Comment

Check Azimuth gearbox oil level. Oil level should be even

 with fill plug. Add oil as required to maintain proper level

Check Azimuth chain and sprockets for dirt. Clean and lubricate

as needed.

Lubricate with good commercial quality spray lubricant

Check Elevation gearbox oil level. Oil level should be even

with fill plug. Add oil as required to maintain proper level.

Check Elevation Jack boot for damage or deterioration.

 Clean dirt and oil from boot as required.

Use  soap and water for cleaning

Check cables and connectors for damage or deterioration.

Clean as required to prolong life.

Use electrical contact cleaner as required

Check wiring for strain relief, damage or deterioration.

Clean as required to prolong life.

Troubleshooting

Troubleshooting Tips
Item

Symptom

Recommended Action

1

Antenna will not drive.

x

Check for  mechanical interference

x

Check power source

x

Check fuses in drive cabinet

x

Check limit switch status/operation

x

Refer to controller maintenance manual for further options

2

Feed polarization will not drive.

x

Check for mechanical interference

x

Check power source

x

Check fuses in drive cabinet

x

Check limit switch status/operation

x

Refer to controller maintenance manual for further options

3

Low signal strength

x

Check pointing of antenna and re-peak as required if mis-pointed

x

Check feed assy for damage or water ingress

x

Check waveguide for damage or water ingress

x

Check cables for damage or poor connections

Appendix B

Summary of Contents for 3.8m Offset Antenna

























Reviews: