manualshive.com logo in svg

Cobalt Digital Inc 250 BOWRIDER, Owner'S Manual

Share
Download
Cobalt Digital Inc 250 BOWRIDER Owner'S Manual Download Page 87

262 Owner’s Manual

3-35

Operating Information

2. Install tonneau support pole(s) to underside of 

the cover (just in front of rear seat) with snap 
and adjust pole to approximate height of 
windshield. Some models have two support 
poles. Make sure the poles are perpendicular to 
the floor and adjust to “tent” the cover.

3. Pull elastic cords over discs on transom, 

starting in the center and working outboard (you 
may have to readjust the support poles for 
proper fit).

4. Continue snapping up the sides.

5. The walk-thru doors may be closed if desired.

Do not use cockpit tonneau cover for extended 
storage. It is not designed for storage, but can be 
used for overnight storage or trailering.

BIMINI TOP - OPTIONAL

1. Remove the stainless adjustable arms from the 

storage area.

2. Unfold the top and install the stainless 

adjustable arms (tensioners) into the 
quick-disconnect fittings on the deck, forward of 
the windshield. Secure the forward arms to the 
forward cross members with the pins.

3. Tighten the bimini by twisting the tensioners.

Do not trailer with the bimini top up. Store and 
trailer the bimini top in the stowed position, in its 
canvas boot.

1. Bimini Enclosure - Optional

Your bimini is equipped with zippers to accept a 
bimini enclosure. This enclosure is made of 
Sunbrella canvas and isinglass. To install:

1. Start zipping the front, sides and aft curtain to 

the zippers on the bimini top, but do not zip 
completely.

2. Snap to the snaps on your deck and windshield 

and then zip completely.

The supports can be adjusted for a better fit.

Always roll the curtains instead of folding when 
storing. Do not use the canopy top, side curtains 
and stern curtain for storage. These are for short 
term storage and not designed for long term 
storage, and will not provide adequate ventilation to 
prevent mold or mildew from forming. Refer to 

Section 5

, 

Interior and Exterior Care

 for 

information on care. For long term storage, see 
your authorized Cobalt dealer.

SKI TOW PYLON - 
REMOVABLE

Remove ski pylon from starboard motor box 
storage compartment by pulling the lock button 
outward and opening the hold down bracket.

To install:

• Insert ski pylon into the base on swim platform 

with rope “finger” pointed to starboard. Push 
pylon down and rotate 1/4 turn clockwise to 
lock in place.

• Press cover plate post onto pylon ring and 

make sure pylon is secure.

To remove:

• Release the cover plate from the pylon ring, 

pull up and rotate pylon 1/4 turn 
counter-clockwise to remove.

• Return the ski pylon back to its hold down 

bracket. Make sure the hold down bracket is 
secure.

NOTICE: Always double check 
snaps are secure.

COB_01

38

_A

COBAL

T

BOW TONNEAU
(BOW RIDER

S

 ONLY)

COCKPIT
TONNEAU

COB_262_OM_forWeb.book  Page 35  Friday, June 9, 2006  3:14 PM

Summary of Contents for 250 BOWRIDER





























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands