background image

OWNER’S MANUAL

 

PURFIKT SPA

2021

 

21

DRAINING AND WINTERIZING

DRAINING YOUR SPA 

After  a  period  of  3-4  months,  detergent  residues  from  bathing 
suits  and  soap  film  will  build  up  in  your  spa  water.  Once 
this happens, your spa water will appear cloudy and should 
probably be replaced. 

Turn power OFF at the breaker.

Locate the drain valve (usually in the equipment area).

Remove the safety cap and attach garden hose.

Drain water to a convenient area (Spa water may harm grass
or plants if sanitizer levels are high.)

When water begins to flow out of the hose, open the air relief
valve  located  on  filter  lid  (Hydro-Cyclonic  Filtration)  or  Air
Bleeder Valve (Skim Filtration).

Your spa will drain except for a small portion left in the foot
well. This can be removed with a sponge and pail.

Once empty, clean as required.

To finish, remove garden hose and attach safety cap.

IMPORTANT  (Cascade  Series  Only): 

There  will  be  an 

additional  drain  valve.  This  is  connected  directly  to  the  tank 
reservoir and you will see the water level go down on the sight 
tube in the equipment area. 

WINTERIZING YOUR  SPA 

In many areas of the world the temperature may drop below 32°
F (0°C). We recommend the spa is always filled with water and 
running  at  normal  spa  temperatures.  By  doing  this  you  will 
minimize the risk of freezing within your spa. If it is necessary to 
leave your spa unattended for long periods of time during cold 
weather  conditions,  you  should  drain  your  spa  to  avoid 
accidental freezing caused by power outages. 
Your  local  dealer  can  perform  the  following  winterizing 
procedures, if you are not completely comfortable with them. 

 

Ensure  that  you  have  fully  drained  the  spa  (Refer  to  the
DRAINING YOUR  SPA section).

 

After draining, your spa may still have water remaining in the
equipment  and  plumbing  fittings.  Disconnect  the  hand-
tightened union fittings going to and from the jet pumps. Be

careful not to lose the O-rings between the unions and pump 
housing. 

Leave drain valve in the open position and safety cap off .

To  completely  drain  the  plumbing  lines,  a  wet/dry  shop
vacuum can be used to draw out any remaining water. Place
the vacuum hose over the jet fittings in the spa as well as the
plumbing  lines  in  the  equipment  area.  You  should  also
disconnect  the  plug  on  the  crystal  clear  inspection  tube  (if
installed).

Remove the filter cartridge and store in a warm, dry area.

Clean the spa shell and place spa cover on spa. Be sure to
lock the cover in place in case of high winds or rain.

WARNIN

G

The  instructions  above  should  be  followed 

accordingly  when  winterizing  your  spa  however  they  are 
guidelines  and  potential  freeze  damage  may  still  occur.  All 
freeze damage is the sole responsibility of the spa owner and 
will not be covered by the warranty should it occur. 

EMER

G

EN

C

Y  SITUATIONS: 

To  eliminate  freezing  in  the 

event  of  equipment  failure,  use  a  100-watt  light  bulb  or  small 
heater  via  extension  cord  and  place  it  in  the  equipment  area, 
keeping it away from plumbing lines. This will help for a short 
period of time until proper service can be rendered. 

Summary of Contents for Purfikt Spa







































Reviews: