background image

 

6.

 

Man down alarm 

 

Falling by breathing dangerous gases can cause serious injury and even fatality to workers. If the 

Man down alarm function in SAN-10 is set on, SAN-10 can detect falls and send a man down   

alert which will activate the audible and visual alarms and alert other people in the area. 

 

 

The man-down detection uses a three-axis accelerometer to automatically monitor the user’s 

movements. If a sudden fall/impact is followed by a  lack  of  movement  for  6  seconds,  the 

alarm will sound. Turn off the alarm by pressing either of the two buttons. 

 

See Section 2.2 Menu and Configuration Settings, to change settings. 

 

7.

 

Reset Button 

Users can reset the unit by pushing a reset button through a 

hole on back of shell. 

 

 

 

 

 

 

 

 

MAINTENANCE

 

 

Calibration

 

The SAN-10 comes pre-calibrated from the factory. However, the CO2 sensor should be calibrated 
at least once a year, or as described in your company’s safety procedures. You can perform the 

calibration yourself, or you can return it to CO2Meter for factory calibration at a nominal fee. 

 

The temperature and humidity sensors do not require calibration and should remain accurate for 

the life of your unit. 

 

Cleaning and Storage

 

Attention: Do NOT use soap, alcohol, aromatic hydrocarbons, or chlorinated solvents for SAN-10 

cleaning purposes. 

The front cover and case can be cleaned with a mild solution of 

detergent and water. 

Apply sparingly with a soft cloth and allow to dry completely prior to using. 

Summary of Contents for SAN-10










Reviews: