should be used as suitable protection
for the counter top incorporated in the
appliance. Use of unsuitable protectors
may cause accidents.
- WARNING: Accessible parts will become
hot when in use. To avoid burns and
scalds children should be kept away.
Insert in the fixed wiring a mean for
disconnection from the supply mains
having a contact separation in all poles
that provide full disconnection under
overvoltage category III conditions, in
accordance with the wiring rules. The
plug or omnipolar switch must be easily
reached on the installed equipment.
This appliance is not intended to be used
via an external timer or a remote control
system.
The manufacturers decline any
responsibility in the event of non-
compliance with what is described above
and the accident prevention norms not
being respected and followed.
To avoid all risk, if the power cable
becomes damaged, it must only be
replaced by the manufacturer, by an
authorized service centre, or by a
qualified electrician.
User’s Instructions
Installation
All operations relative to installation (electric connection)
should be carried out by skilled personnel in conformity with
the rules in force.
As for the specific instructions see part pertaining to installer.
Use
TOUCH CONTROL HEATING ELEMENTS
Touch sensitive keys
All operations can be performed using touch sensitive keys
(capacitive sensors) located on the front of the control
board; each key has a corresponding display. All actions are
confirmed by an audible signal.
TOUCH CONTROL (Fig. 1)
1 Power ON/ Power OFF
2 Cooking zone
3 Setting display
4 Minus
5 Plus
6 Dual circuit
7 Timer
8 Timer display
9 Lock function
10 Dual circuit indicator light
11 Timer indicator lights
12 Lock indicator light
13 Decimal point
Switching the Touch Control ON/OFF
After mains voltage is applied the control initializes for
approx. 1 second before it is ready for operation. After a reset
all displays and LEDs glow for approx. 1 second. When this
time is over all displays and LEDs extinguish and the control
is in the stand-by mode.
By operating the ON/OFF key the control can be turned into
the ON-mode. The cooking zone displays show a static “0“.
If a cooking zone is in the “hot“ status, the display shows a
static “H“ instead of “0“. The bottom right dot is blinking in 1
second intervals on all cooking zone displays to indicate that
no cooking zone is selected at the moment.
After switching-ON the electronic control remains activated
for 10 seconds. If no cooking zone or timer selection follows
within this period of time, the electronic control automatically
switches back into the stand-by-mode.
The control can only be switched-ON if it identifies the ON/
OFF key (1) alone being operated. Should it recognize key
activation other than that, the control remains in the standby-
mode.
If the child safety feature is active when switching on, all
cooking zones show “L“, (LOCKED). (also refer to 1.11). If
the cooking zones are in a “hot“ status, the display shows
“L“ and “H“ in alternation. When the Touch Control is ON it
can be switched-
OFF at any time by operating the ON/OFF key (1). This is also
valid if the control has been locked (activated child safety
feature).
The ON/OFF key (1) has always priority in the switch-OFF
function.
Automatic switch-OFF
When the control is ON it automatically switches-OFF after
10 seconds if no cooking zone or select key has been
operated within this period of time.
Switching a cooking zone ON and OFF
If the control is ON the respective cooking zone can be
selected by operating a cooking-zone-select-key (2). There
is a static dot indication in the respective display. If the
Summary of Contents for NODOR V2170SLBK
