Club Car 2005 FE290 Maintenance Service Supplement Download

Page: 87 / 168

FE290 ENGINE

Ignition Coil and Flywheel

2005 FE290 Gasoline Vehicle Maintenance and Service Supplement

Page 13-7

IGNITION COIL AND FLYWHEEL

See General Warning, Section 10, Page 10-1.

Ignition Coil and Flywheel Removal

1. Loosen three screws and remove the remaining four screws attaching the flywheel housing as shown,

then remove the housing

(Figure 13-7, Page 13-7).

2. Disconnect the ignition coil (1) from its primary lead wire at the connector (2). Remove the two bolts (3)

and take out the ignition coil

(Figure 13-8, Page 13-7)

Figure 13-6 Crankcase Cover Installation

Figure 13-7 Flywheel Housing

Figure 13-8 Ignition Coil

Loosen.

Remove.

Summary of Contents for 2005 FE290









































































































































































Search results

Summary of Contents for 2005 FE290

Reviews:

Related manuals for 2005 FE290

Brands by name

Popular brands

Club Car 2005 FE290, Maintenance Service Supplement

Search results

Summary of Contents for 2005 FE290

Reviews:

Related manuals for 2005 FE290

Brands by name

Popular brands