ClosetMaid MAXLOAD 35354 Installation Instructions Manual Download Page 1

Page: 1 / 58

35354 02/20

01-82371-00

2 SHELF KIT (3 FT.)

INSTALLATION INSTRUCTIONS

What you will need:

•  Please read all instructions carefully.
•  Familiarize yourself with all parts (see “PARTS INCLUDED WITH KIT”) and check quantities.
•  Follow all safety precautions (see “SAFETY PRECAUTIONS”).

• Follow all manufacturer installation requirements in order to comply with the

advertised weight load specifications.

BEFORE BEGINNING

*Static Load Evenly Distributed. Must be installed per manufacturer’s

specifications or weight load capacity does not apply.

Whichever load reaches

capacity first:

Maximum Shelving Load*: 100 lbs/ft
Maximum 40 in. Hang Track Load*: 700 lbs
Maximum System Load*: 600 lbs

(See pages 6)

Summary of Contents for MAXLOAD 35354



























































Search results

Summary of Contents for MAXLOAD 35354

Reviews:

Related manuals for MAXLOAD 35354

Brands by name

Popular brands

ClosetMaid MAXLOAD 35354, Installation Instructions Manual

Search results

Summary of Contents for MAXLOAD 35354

Reviews:

Related manuals for MAXLOAD 35354

Brands by name

Popular brands