manualshive.com logo in svg

ClimExel DH-120, Installation And Operating Instructions Manual

Share
Download
ClimExel DH-120 Installation And Operating Instructions Manual Download Page 2

16/28

2015/12 - Indice de révision : B - Code : 33491

 

„

SAFETY INSTRUCTIONS AND RECOMMENDATIONS  ..............................17

Children and physically or mentally impaired persons: ........................................................17
Electrical safety: ...................................................................................................................17
Fire safety: ............................................................................................................................17

OPERATING PRINCIPLE ...............................................................................18

 

„

DIMENSIONS AND TECHNICAL DATA  ........................................................19

 

„

INSTALLATION  ..............................................................................................20

 

„

WIRING ...........................................................................................................21

 

„

COMMISSIONING AND USE .........................................................................22

Connection of the device to the mains: ................................................................................22
Start up: ................................................................................................................................22
Selection of the operating mode: ..........................................................................................22
Setting the humidity set point: ..............................................................................................22
Setting the temperature set point (if the heating option is installed and active): ..................23
Programming a postponed start and a postponed stop:  ......................................................23
Selecting the fan operating speed:  ......................................................................................24
Automatic defrosting: ............................................................................................................24
Shutting down the device: ....................................................................................................24
Locking/ unlocking the control pad: ......................................................................................24
Verifying and setting and the operating parameters: ............................................................24

 

„

INSTALLATION OF THE HEATING ELEMENT (OPTION)  ...........................25

 

„

MAINTENANCE - UPKEEP ............................................................................27

 

„

ERROR CODES AND TROUBLESHOOTING: ..............................................28

Error codes:   ........................................................................................................................28
Trouble shooting: ..................................................................................................................28

Summary of Contents for DH-120















Reviews:

No comments

Brands by name

Popular brands

Load more brands