Climecon CLEANMASTER Series Installation Manual Download

Page: 24 / 27

climecon.fi

Lämmittäjänkatu 4 A, 00880 Helsinki, FINLAND · Tel. +358 (0)20 198 6600

17. Climecon CleanMaster® – updating an external controller

IMPORTANT! Before updating the external controller, the CleanMaster® hood/IV ceiling hardware has to be

updated. See

‘Climecon CleanMaster 2G – software update.pdf’

Detach the external controller’s cord.

Press the

‘Home’ + ‘ESC’ buttons and hold them down.

Reattach the external controller’s cord.

Note! Hold the buttons down during this.

Wait until the screen displays the following text:

‘Formatting external UI flash…’.

Release the buttons.

Wait until the screen’s start sequence is ready.

During the sequence, the text

‘Starting’ is displayed on

the screen. The start will last a few minutes.

The device has been updated and is ready for use.

Summary of Contents for CLEANMASTER Series




























Search results

Summary of Contents for CLEANMASTER Series

Reviews:

Related manuals for CLEANMASTER Series

Brands by name

Popular brands

Climecon CLEANMASTER Series, Installation Manual

Search results

Summary of Contents for CLEANMASTER Series

Reviews:

Related manuals for CLEANMASTER Series

Brands by name

Popular brands