background image

Installation Manual 

97B0055N03

Rev.: 2/24/14

ATC32U02 iGate

 Communicating, 

Programmable Thermostat

Table of Contents

Caution:

These instructions are intended to be used by the installer or service personnel.  End users are NOT advised to change or 
modify any of these settings.  Doing so may cause the equipment to stop working properly and/or may void the warranty on 
both the thermostat and the equipment.

Section Title 

Page

 

 

Safety/Installation Considerations  

  3

1.0  

User Menu Settings  

  4

2.0  

Installer Menu Settings  

  6

 

2.1  

Installer Menu Settings Access  

  6

 

2.2  

Thermostat Confi guration  

6

3.0  

System Confi guration  

7

 3.1 

  Airfl ow Selection  

7

 

3.2  

Option Selection  

7

 

3.3  

Unit Confi guration  

8

 

3.4  

Pump Confi guration  

8

 

3.5  

Valve Confi guration 

9

 

3.6  

Multi-Unit Confi guration  

9

4.0  

Accessory Confi guration  

10

 

4.1  

Air Filter  

10

 4.2 

  Humidifi er  

10

 

4.3  

UV Lamp  

10

Section Title 

Page

 

4.4  

Air Cleaner 

10

5.0  

Input Dealer Information  

10

6.0  

Humidity Confi guration  

11

7.0  

Temperature Algorithm  

11

8.0  

Demand Reduction Confi guration  

12

9.0  

Service Mode  

12

 

9.1  

Manual Operation  

12

 

9.2  

Control Diagnostics  

12

 

9.3  

Dipswitch Confi guration  

13

 

9.4  

Fault History  

13

 

9.5  

Clear Fault History  

14

 

9.6  

Multi-Unit Diagnostics  

14

 

9.7  

Multi-Unit Fault Information  

15

10.0  

Restore Defaults  

15

11.0  

Revision History  

16

Summary of Contents for iGate ATC32U02

















Reviews: