manualshive.com logo in svg

ClearSpan 103564, Instruction Manual

Share
Download
ClearSpan 103564 Instruction Manual Download Page 12

CLEARSPAN

™

 SUNBLOCKER PRO SHADE

12

Revision date: 09.16.09

FINAL FRAME INSPECTION FOR 

COVER INSTALLATION

Before the cover is installed, complete 

these steps to prepare the frame for 

cover installation.
1.  Verify that all fasteners are installed 

and tight.

2.  Inspect the frame for fasteners 

that are installed in areas where 

the main cover meets the frame. 

Reposition these fasteners (if 

possible) or wrap with tarp or duct 

tape to protect the cover.

3.  Inspect all pipe and connections for 

sharp edges and file smooth and/or 

wrap with duct tape.

5

SIDE STRUT INSTALLATION

Complete these steps to install the four (4) side struts:
1.  Locate one strut and position it between one first interior rafter leg and the leg of the second interior 

rafter as shown below.

2.  Attach one end of the strut to the previously installed band clamp as shown in the diagram below.  

 

NOTE:

 Head of bolt on the band clamp must face the outside.

3.  Attach the remaining end of the strut to the baseboard using a customer-supplied wood screw. See 

the diagram below for location. 

 

NOTE:

 A baseboard provides a place to attach each strut and helps keep the ground posts at the 

required depth. The customer is responsible for providing a baseboard for this frame.  

 

If no baseboard is used, pre-drill mounting hole in ground post, reposition strut and attach using a 

customer-supplied fastener.

4.  Repeat the above steps to attach the remaining side struts to the shelter.
5.  After securing the struts, verify that all clamps are secured with a Tek screw to the rafters.

End 

Rafter

Ground Level

Baseboard

Baseboard is required to 

secure strut as shown. 

Strut

Interior

Rafter

Strut

End Rafter

Band 

Clamp

Photo shows the strut 

attached to the inside of 

the customer- supplied 

baseboard.

Attach strut to baseboard 

using customer-supplied 

wood screw.

Struts

Summary of Contents for 103564


























Reviews:

No comments

Brands by name

Popular brands

Load more brands