manualshive.com logo in svg

Clearfield FieldSmart, Installation Manual

Share
Download
Clearfield FieldSmart Installation Manual Download Page 19

19

FieldSmart

®

 FxDS Frame

__________________________________________________________

Installation Manual

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeClearfield.com • [email protected] 

Manual 012010 REV H - July 2018

When bringing fiber to a patch & splice panel, to store the 

required slack, you should use radius limiter assemblies (P/N 

010600) in pairs. This part number is ordered and shipped 

separately from the frame kit or panels.

Patch and Splice Panels

Buffer tube storage on radius limiter assemblies shown here.

Note:

 Using the cable clamps, cables can be secured to either side 

of the the cable mounting brackets.

Once you have the desired slack stored (including an additional 

3ft/1m of fiber for splicing), remove the cassettes from the panel. 

Bring your fiber through the front of the frame and proceed to 

splicing in your cassettes

Re-store the slack and mount the cassettes back into the panel.

1.

2.

3.

4.

5.

Note:

 

Consult the Clearview Blue Cassette Installation Manual for splicing instructions. Viewable in the Installation Manual 

section, under the Resources tab, of the Clearfield website. Link here:

https://www.seeclearfield.com/assets/documents/installation-manuals/clearview-blue-cassette-install-manual.pdf

. 

Summary of Contents for FieldSmart






























Reviews:

No comments

Brands by name

Popular brands

Load more brands