manualshive.com logo in svg

Clearfield FieldSmart 144, Installation Manual, Page: 26 / 46

Share
Download
Clearfield FieldSmart 144 Installation Manual Download Page 26

Direct: 763.476.6866 • National: 800.422.2537 • www.SeeClearfield.com • [email protected] 

26

FieldSmart

®

 Fiber Distribution Hub (FDH)

Installation Manual 

 _________________________________________________________

Manual 019703 REV B - March 2019

5. Remove the plugs from selected holes in the entrance 

plate and feed the cables through. Ensure the 

entrance plate gasket is around the cables and below 

the entrance plate before proceeding.

Compression Fitting Grommet

Cable Size (Inches)

Small Black Grommet

0.3 - 0.4

Medium Black Grommet

0.41 - 0.5

Gray Grommet (Comes Pre-Installed)

0.51 - 0.79

Large Black Grommet (Comes Pre-Installed)

0.71 - 0.98

6. Select the 

compression fitting 

grommet size that 

most nearly fits the 

cable to be installed. 

The grommets are 

included in the 

ship-along hardware.

Note:

 If more sealcons or strength member clamps are needed, speak to your sales representative about a cable expansion 

kit, part number FMA-XXX-14.

Summary of Contents for FieldSmart 144















































Reviews:

No comments