background image

36456-E3H-Raptor CE (04-01) 

3

OPERATION 

SAFETY PRECAUTIONS 

This machine is intended for commercial use. It is 
designed to wet clean carpet and upholstery in a 
indoor environment and is not constructed for any 
other use. Use only recommended cleaning solutions 
and accessory tools. 

All operators must read, understand and practice the 
following safety precautions. 

The following safety-alert symbols are used throughout 
this manual as indicated in their description: 

  WARNING: To warn of hazards or unsafe 

practices which could result in severe personal 
injury or death. 

FOR SAFETY: To identify actions which must be 
followed for safe operation of equipment. 

The following information signals potentially dangerous 
conditions to the operator or equipment. 

FOR SAFETY: 

1.  Do not operate machine: 
 

– 

Unless trained and authorized. 

 

– 

Unless operator manual is read and 
understood. 

 

– 

In flammable or explosive areas.  

 

– 

With damaged cord or plug. 

– 

If not in proper operating condition. 

– 

Unless cord is properly grounded. 

 

– 

In outdoor areas.  

 

– 

In standing water. 

 

– 

With the use of an extension cord. 

2.  Before operating machine: 

 

– 

Make sure all safety devices are in place 
and operate properly. 

3.  When using machine: 
 

– 

Do not run machine over cord. 

 

– 

Do not pull machine by plug or cord. 

 

– 

Do not pull cord around sharp edges or 
corners.  

 

– 

Do not unplug by pulling on cord. 

 

– 

Do not stretch cord. 

 

– 

Do not handle plugs with wet hands.  

 

– 

Keep cord away from heated surfaces.  

– 

Report machine damage or faulty operation 
immediately.  

– 

Follow mixing and handling instructions on 
chemical containers.  

– 

Connect hoses before turning on pump. 

– 

Be sure chemicals are safe and non-toxic. 

4.  Before leaving or servicing machine: 

– 

Turn off machine. 

– 

Unplug cord from wall outlet. 

5.  When servicing machine: 

– 

Unplug cord from wall outlet. 

– 

Avoid moving parts. Do not wear loose 
jackets, shirts, or sleeves.  

– 

Use manufacturer supplied or approved 
replacement parts.  

   WARNING: Hazardous Voltage. Shock or 

electrocution can result. Always unplug machine 
before servicing. 

   WARNING: Flammable materials can cause 

an explosion or fire. Do not use flammable 
materials in tank(s). 

   WARNING: Flammable materials or reactive 

metals can cause an explosion or fire. Do not pick 
up. 

   WARNING: Hot solutions up to 88° C (190°F). 

Do not touch with any part of the body. Use 
thermometer to gauge temperature. 

   WARNING: Contents of solution hoses may 

be under pressure even after pump is off. 

 

GROUNDING INSTRUCTIONS 

Machine must be grounded. If it should 
malfunction or breakdown, grounding provides a 
path of least resistance for electrical current to 
reduce the risk of electrical shock. This machine is 
equipped with a cord having an equipment-
grounding connector and grounding plug. The 
plug must be plugged into an appropriate outlet 
that is properly installed in accordance with all 
local codes and ordinances. Do not remove 
ground pin; if missing, replace plug before use. 
International models will have different cord ends.

 

GROUNDED OUTLET 
            (3 HOLE) 

GROUNDING 
        PIN 

Summary of Contents for Raptor 230H






















Reviews: