manualshive.com logo in svg

Clayton Scorpion SC-100 Series, Safety, Operation & Maintenance, Page: 6 / 14

Share
Download
Clayton Scorpion SC-100 Series Safety, Operation & Maintenance Download Page 6

Repair or Warranty Contact

 

Clayton Associates, Inc. 

•

 1650 Oak Street 

•

 Lakewood, New Jersey 08701 

•

 P.+1-732-363-2100 F.+1-732-364-6084

 

www.DustlessMadeSimple.com 

•

 [email protected]

Page 6

If this vacuum is used to collect hazardous material, appropriate personal protective equipment may be required.
The vacuum should be emptied when half full or when dust accumulation in the vacuum degrades performance.

 

1. Safe the Vacuum

• Disconnect the compressed air source from the vacuum

• Disconnect the vacuum hose

2. Remove the Inlet Cap

• Hold the vacuum canister and rotate the inlet cap counterclockwise approximately 1 full turn 

• Remove the cap from the canister and set aside

3. Empty the Canister

• Discard the contents of the canister in an approved waste receptacle

4. Replace the Inlet Cap

• Clean / Wipe the top edge of the canister to ensure a good seal when the inlet cap is attached

• Replace the inlet cap on the canister and rotate clockwise approximately 1 full turn until snug

EMPTY THE VACUUM

Inlet Cap

Canister

Top Edge of Canister

Summary of Contents for Scorpion SC-100 Series















Reviews:

No comments