manualshive.com logo in svg

Clayton Scorpion SC-100 Series, Safety, Operation & Maintenance, Page: 4 / 14

Share
Download
Clayton Scorpion SC-100 Series Safety, Operation & Maintenance Download Page 4

COMPRESSED AIR FITTINGS

Repair or Warranty Contact

 

Clayton Associates, Inc. 

•

 1650 Oak Street 

•

 Lakewood, New Jersey 08701 

•

 P.+1-732-363-2100 F.+1-732-364-6084

 

www.DustlessMadeSimple.com 

•

 [email protected]

Page 4

1. The vacuum has the following compressed air requirements to function properly

• Compressed air must be clean, dry, and oil free to prevent blockage of the pneumatic system

• Compressed airline must have a minimum diameter of 3/8in

2. Compressed Air Plug (air in)

The Vacuum is supplied with a 1/4in industrial interchange compressed air plug for connection to your compressed air supply.

The compressed air plug may be changed to another nominal 1/4in style if required

• Hold the compressed air bushing with a 3/4in open end wrench

• Remove the compressed air plug with either a 9/16in deep socket or 9/16in open end wrench

• Install a new compressed air plug

3. Compressed Air Coupler (air out)

The Vacuum is supplied with a 1/4in brass high flow compatible industrial interchange compressed air coupler.
This coupler provides convenient pass through compressed air for an air tool connected to the vacuum.

  The compressed air coupler may be changed to another nominal 1/4in style if required

  • Hold the compressed air bushing with a 3/4in open end wrench

  • Remove the compressed air coupler with a 3/4in open end wrench
  • Install a new compressed air coupler

Compressed Air Plug

Compressed 

Air Coupler

Compressed 

Air Bushing

Compressed 

Air Bushing

Summary of Contents for Scorpion SC-100 Series















Reviews:

No comments