manualshive.com logo in svg

Clayton Scorpion SC-100 Series, Safety, Operation & Maintenance, Page: 5 / 14

Share
Download
Clayton Scorpion SC-100 Series Safety, Operation & Maintenance Download Page 5

Repair or Warranty Contact

 

Clayton Associates, Inc. 

•

 1650 Oak Street 

•

 Lakewood, New Jersey 08701 

•

 P.+1-732-363-2100 F.+1-732-364-6084

 

www.DustlessMadeSimple.com 

•

 [email protected]

Page 5

BEFORE EACH USE

1. Visually inspect vacuum to ensure that no parts are missing or damaged
2. Empty the Vacuum if required 

• See the Emptying the Vacuum section of this document

3. Install a new HEPA Filter if required

• See the HEPA Filter Change section of this document

4. Install a new Pre-Filter  if required

• See the Pre-Filter Change section of this document

5. Attach the Compressed Air Line

• Ensure that the compressed air valve on the vacuum is in the off position

• Connect the compressed airline to a compressed air source

• Connect the compressed airline to the compressed air plug on the vacuum

6. Attach Vacuum Hose

Vacuum Hose only

• Press the vacuum hose cuff onto the 

Vacuum Inlet

Combination Air/Vac Hose

• Press the vacuum hose cuff onto the 

Vacuum Inlet

• Connect the compressed air plug  to the compressed 

air coupler on the vacuum

7. Activating the Vacuum

• Rotate the compressed air valve on the vacuum 

45 degrees forward to start compressed 

air flowing and activate the vacuum

Compressed 

Air Valve Off

Compressed 

Air Plug

Vacuum

Hose Cuff

Compressed 

Air Plug 

Compressed Air 

Valve On 

Vacuum Inlet

Compressed 

Air Coupler

Compressed Airline

Summary of Contents for Scorpion SC-100 Series















Reviews:

No comments