System Menu
Memory Protect – On, Off
This is set to “On” when the Nord C2 leaves the factory, meaning that
you cannot save any changes to the programs . Set this to Off when you
wish to store your own programs . The System, MIDI or Sound menu
settings and the Live memory are not protected by this setting .
Range: On (default), off
Output Routing L/R
If you want to process your sound using external effects or separate
amplifier systems, it can be convenient to route organs to separate
outputs of the Nord C2 . This setting determines which organs should
be routed to the main left & right outputs .
Range: P - Pipe organ.
Pb - Pipe organ and the B3 model.
PE - Pipe organ and the VX and Farf models.
A - All models.
If the High Level or 11-pin output is not connected, all organs will
E
be routed to the L&R outputs.
Output Routing Ext. Rotary Spkr
This setting determines which organs should be routed to the 11-pin
and High Level outputs .
Range: b3 - B3 model.
E - The VX and Farf models.
bE - The B3, the VX and the Farf models.
If the High Level or 11-pin output is not connected, all organs will
E
be routed to the L&R outputs.
Transpose
Transpose allows you transpose the pitch of the Nord C2 up or down in
semitone steps .
Range: -/+ 6 semitones (default = 0).
Fine Tune
This allows you to fine tune the pitch of the Nord C2 .
Range: +/- 50 cent (default = 0).
Sustain Pedal Polarity
This allows you to change the polarity of a connected sustain pedal, in
case the functionality of your pedal is reversed (i .e . when the pedal is
up, sustain is on and vice versa) .
Range: OP - Open, CL - Close (default).
Sustain Pedal Configuration
Controls weather the selected organ model should respond to sustain
pedal messages or not . When a pedal is connected to the sustain
pedal input, sustain pedal messages are always send via MIDI Out
regardless of this setting .
Range: On (default), Off.
The pipe organ is never affected by a sustain pedal.
M
Rotor Ctrl. Type
Specifies the type of controller connected to the Rotary Control input .
Range: HA - Halfmoon, OP - Open, CL - Closed (default).
Swell Pedal Type
Different brands of control pedals have different specifications (resistance,
offset and linearity) . To simplify setup and to optimize the response of the
pedal for the Nord C2, the most common pedal makes are pre-config-
ured, and you simply select the type of pedal you connect .
Roland, Yamaha and Fatar are linear control pedals with different scal-
ing and offset . Ernie Ball pedals (“ErnieB”) are marketed as volume ped-
als, with a logarithmic response, but the response is rescaled internally
in the Nord C2 to make them work nicely as control pedals . They may
need a Y-cable (stereo plug -> 2 mono plugs) to work with the Nord C2 .
Range: FA - Fatar, Er - Ernie Ball, YA - Yamaha, rO - Roland
(default)
6
The Menus
Any settings that you change in the
System
,
MIDI
or
Sound
menu will take immediate effect on a global basis, and will be stored until you change
them the next time * . Enter the menus by pressing and holding Shift and the System, MIDI or Sound button (Prog, Live 1 or Live 2) . Select a function
with the Up/Down buttons and change the setting by pressing and holding Shift and the Up or Down button . Exit the menus by pressing a second
time on the Prog, Live 1 or Live 2 button .
* The only exception to this is the MIDI Local On/Off setting which always reverts to Local On every time the Nord C2 is powered up.
M
6themeNUs
| 17
Summary of Contents for Nord C2
Page 25: ......
