51000133 Iss 01
MODEL
This unit is a 6kW commercial heater designed for
mounting on the wall to be used as a space heater. It is
supplied complete with remote mounting control box.
MOUNTING
The unit should be fitted between 2.5 to 3 meters from
ground level. The angle of the heater can be adjusted in
steps, 45 deg. vertically and 180 deg. horizontally.
The unit should be positioned so that the airflow is not
obstructed. When installed the top of the heater case
should be a minimum of 200mm from the ceiling. Never
install heaters opposite to each other.
INSTALLATION
The wall bracket is secured to one of the inner
cardboard box corners. Cut the plastic bag to remove it.
All fixing screws, switch and parts for the swivel bracket
are packed under the terminal cover. Carefully unpack
the unit and remove the terminal cover.
NOTE:
The heater must always be installed
horizontally
, using the mounting bracket provided. This
ensures correct positioning and adequate clearance.
Assemble the swivel bracket as shown on Fig.2. Use M8
and M5 bolts with locknuts and washers as supplied in a
bag. Attach the assembled bracket to the bottom of the
heater by using 4 x M6 bolts with plain and spring
washers as shown on the Fig.3.
Fig 2
SWIVEL BRACKET ASSEMBLY
Fig 3
SWIVEL BRACKET ASSEMBLY
Secure the wall bracket to the wall with suitable
fixings. Ensure the position of this bracket will allow
suitable clearances between the heater, when fitted,
and adjacent walls. Minimum of
3 fixings
must be used
to secure the wall bracket to the wall. The weight of
the heater is
11.5kg
Attach the heater to the wall bracket.
Finally adjust the direction of the heater to the desired
area and tighten up all clamping nuts and bolts.
ELECTRICAL CONNECTIONS
The heater is suitable for connection to 230-240 Volts
single phase 50Hz supply. The heater consumes
approximately 6kW on the full heat setting. The
connections to be made between the heater and the
remote control box are shown in section ‘CONTROLS’.
Earth terminals are adjacent to the terminal block and
are clearly marked with the EARTH symbol. For safety
reasons a good earth connection must ALWAYS be made
to the heater and control box.
The unit must be wired in accordance with IEE
regulations for the Electrical Equipment of Buildings and
the installer should ensure that a suitable fused
isolating switch is connected in the mains supply.
REMOTE CONTROL SWITCH CONNECTIONS
MAINTENANCE
H1 –
HEAT1 3kW
, H2 –
HEAT2 3kW
, F –
FAN
N –
NEUTRAL
, L –
SPARE TERMINAL
, E -
EARTH
CONTROLS
The unit is designed to provide 2 levels of heat;
3kW-6kW together with fan only for air circulation. The
remote control box houses 3 double pole switches to give
the following functions:
SWITCH 1 (left-hand)
ON/OFF / FAN ONLY
SWITCH 2
HEAT I.
SWITCH 2+ SWITCH 3
HEAT II.
FRONT VIEW
One control unit can control only 1 heater.
For more details please see wiring diagram.
ALWAYS ENSURE THAT THE MAIN EXTERNAL ELECTRICITY
SUPPLY IS SWITCHED OFF BEFORE SERVICING OF THIS
HEATER.
To obtain the best results from the heater it is essential
to avoid the accumulation of dust and dirt within the
unit and on the inlet and discharge grilles. Regular
cleaning is necessary with particular attention to the
fronts and backs of the fan motor blades. Cleaning of
the fan is best carried out with a soft brush.
THERMAL CUT-OUT
The units are protected from overheating in the event of
fan failure or an obstruction of the free airflow, by two
thermal cut outs. If this happens the thermal cut outs
effectively switch off the appliance. The appliance will not
operate until the thermal cut outs are manually re-set.
This should be done by a competent electrician.
RESETING THERMAL CUT-OUT
The cut-outs are located under the top cover on the top
of the heating element.
a) To reset the cut-out, allow the appliance to cool for
20 minutes.
b) Gently press the plastic square button on the top of
the cut-out.
c) Restart, switch ON the appliance.
TO REPLACE A SWITCH IN THE CONTROL BOX
a)
Switch off the mains supply
b)
Remove the switch box cover.
c)
Disconnect the wiring to the switch.
d)
Remove the retaining screw and push out the switch.
e)
Fit the replacement switch, reconnect the wiring and
replace the cover.
SPARES
It is essential when ordering spares or replacement parts
to state the model number CH06CS and the serial
number on the rating place fixed to the top of the unit.
NB: DO NOT COVER ANY OF THE AIR INLET OR OUTLET
GRILLES AT ANY TIME.
In the interest of progress the Company reserves the
right to vary specifications from time to time without
notice. The material listed is offered subject to the
Company’s General Conditions of Sale, a copy of which
can be obtained on request.
Fig 1
OUTLINE DRAWING
