background image

 

 

 
 

-2-

 

CLASSÉ DESIGN PHILOSOPHY

 

 

 

1. REPEATED LISTENING DESIGN SESSIONS: 

Fine tuning of sound by exchanging and mixing of parts (transistors, capacitors, wiring, PCB boards 

etc.), and adjusting many specific operating voltages within proper engineering ranges, producing an 

overall sonic recipe giving the most natural harmonic realism of music typical of instruments in a 

live performance. 

 

2. UPGRADABLE SINGLE CIRCUIT DESIGNS: 

All Classé products (all preamps and all amps) share exactly the same circuit design philosophy 

(excluding moving coil and moving magnet phono circuits). This means all amplifiers and all high 

level circuits of the preamps benefit from the same design goals. Similar circuits are then tailored to 

different power levels etc. Differences between less expensive models and more expensive models 

are parts quality and compliment, power supply extravagance and the amount of filtering etc., as 

well as features and packaging. 

 

This means that for years Classé has been constantly sonically fine tuning and technically upgrading 

this circuit design and its application, thus reaching a very high level of natural musical enjoyment, 

as well as excellent reliability which benefits all models - least expensive, most expensive, preamps 

and amplifiers alike. 

 

3. EXTREME LONG LIFE IN REAL WORLD CONDITIONS: 

Choosing the best attainable quality parts and materials combined with the advantages of the two 

above-mentioned areas provides Classé owners with years of proven trouble free reliability and 

musical enjoyment. 

 

 

Summary of Contents for 175-A











Reviews: