background image

18

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

TROUBLESHOOTING

Problem

Cause

Solution

Bad Battery light 
comes on 
(WBC400 model)

The battery voltage is 
between 0.5V and 1.5V.

Have the battery tested by 
a qualified technician;

Replace the bad battery if 
necessary.

The battery voltage is lower 
than 11V, after being 
charged for 4 minutes.

The battery voltage drops 
below 12V two minutes after 
being fully charged.

Unable to reach fully 
charged status in 24 hours.

Battery does not 
charge

Lack of AC input power.

Make sure that the charger 
is plugged into AC outlet 
and the POWER LED is lit.

Faulty connections to 
battery terminals.

Unplug the charger and 
check the battery 
connection; ensure that 
there is a good connection 
at the battery terminal/post 
and/or vehicle chassis.

Wrong charge voltage 
selection.

Check that the correct 
charge voltage was 
selected for the battery 
being charged.

Battery voltage too low.

Ensure enough charging 
time was allowed to charge 
battery.

Charging a very cold 
battery.

If the battery being 
charged is extremely cold 
(below freezing), it will not 
accept a high rate of 
charge, so the initial 
charger rate will be slow.
The rate of charger will 
increase as the battery 
warms. 
Never attempt to charge a 
frozen battery.

Summary of Contents for WBC240

























Reviews: