background image

8

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

MAINTENANCE

The only maintenance required is a regular inspection to ensure that  debris is
not blocking the passage of water through the pump.

Clean the filter basket periodically
after closing any inlet and delivery
valves and removing the filter cover,
using the wrench provided. Lift out
the filter basket and clean it in water,
check the cover O-ring is in good
condition before reassembly.

If you suspect the pump is blocked
by silt, leaf debris etc, disconnect it
from the mains supply and backflush
to clear any blockage though the
drain plug. You will need to disconnect the outlet hose and lift out the non-
return valve to do this.

Always keep the pump in a clean condition, checking regularly for loose
bolts or a damaged power cable etc.

AFTER USE

After use, and if the pump will not be used over the winter period, or
whenever there is danger of freezing, always drain the pump body. If the
pump has been used with contaminated or salty water, it should be
thoroughly flushed with clean water following use, both inside and out. It
should then be drained before replacing

 

the drain plug, and covered over, if

not already installed in a clean, dry environment sheltered from the weather.
Remember to re-prime the pump when returning to service.

In the event that dismantling and overhaul of the pump is necessary,
contact your CLARKE International Service Department on 020-8988-7400.

ENVIRONMENTAL RECYCLING POLICY

Through purchase of this product, the customer is taking on the
obligation to deal with the WEEE in accordance with the WEEE
regulations in relation to the treatment, recycling & recovery and
environmentally sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with general
household waste. It must be disposed of according to the laws governing
Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal
facility.

Fig 4

O-ring

Filter
Basket

Non-
return
valve

Summary of Contents for SPP07





















Reviews: