background image

4

Parts & Service: 020 8988 7400/E-mail:[email protected] or [email protected]

ELECTRICAL CONNECTIONS

WARNING!  Read  these electrical safety instructions thoroughly
before connecting the product to the mains supply.

Before switching the product on, make sure that the voltage of your
electricity supply is the same as that indicated on the rating plate. This
product is designed to operate on 230VAC 50Hz. Connecting it to any other
power source may cause damage.

This product may be fitted with a non-rewireable plug. If it is necessary to
change the fuse in the plug, the fuse cover must be refitted. If the fuse cover
becomes lost or damaged, the plug must not be used until a suitable
replacement is obtained.

If the plug has to be changed because it is not suitable for your socket, or
due to damage, it should be cut off and a replacement fitted, following the
wiring instructions shown below. The old plug must be disposed of safely, as
insertion into a mains socket could cause an electrical hazard.

WARNING! The wires in the power cable of this product are
coloured  in accordance with the following code:

Blue = Neutral          Brown = Live

Yellow & Green = Earth

If the colours of the wires in the power cable of this product do not
correspond with the terminal markings of your plug, proceed as follows:

The wire which is coloured Blue must be connected to the terminal
which is marked N or coloured Black

.

The wire which is coloured Brown must be connected to the
terminal which is marked L or coloured Red.

• The wire which is coloured Yellow & Green  must be connected to

the terminal which is marked E or      or coloured Green

.

Plug must be BS1363/A approved

Earth

Always fit a 13 Amp fuse.

(Green and Yellow)

Neutral

Live

 (Blue)

        (Brown)

Ensure that the outer sheath of the cable is firmly held by the clamp

Always connect this product to the mains supply via a Residual Current
Device (RCD)

If in any doubt, consult a qualified electrician. DO NOT attempt any repairs
yourself.

Summary of Contents for SPP07





















Reviews: