Clarke METALWORKER CHDBG900 Operation & Maintenance Instructions Manual Download

Page: 3 / 16

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

SPECIFICATIONS

POWER TOOL SAFETY WARNINGS

1) WORK AREA

Keep the work area clean and well lit.

Cluttered and dark areas invite

accidents.

Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust.

Power tools create sparks

which may ignite the dust or fumes.

Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

Model number

CHDBG900

Part number

6500540

Dimensions (D x W x H)

498 x 250 x 300 mm

Weight

26.3 kg

Rated voltage

230V~ 50 Hz

Rated input wattage

900W

No load speed

2850 RPM (+/- 5%)

IP rating

IP40

Wheel shaft diameter

16 mm

Abrasive wheels supplied

Coarse (36 Grit), Fine (60 Grit)

Wheel dimensions

Diameter (200 mm)
Thickness (32 mm)
Bore (32 mm)

Duty Cycle classification

S2/30 minutes

Sound power (measured)

97 dB LpA

Sound power (guaranteed)

98 dB LwA

Uncertainty factor K

1.67 dB

Summary of Contents for METALWORKER CHDBG900

















Search results

Summary of Contents for METALWORKER CHDBG900

Reviews:

Related manuals for METALWORKER CHDBG900

Brands by name

Popular brands

Clarke METALWORKER CHDBG900, Operation & Maintenance Instructions Manual

Search results

Summary of Contents for METALWORKER CHDBG900

Reviews:

Related manuals for METALWORKER CHDBG900

Brands by name

Popular brands