Clarke JS900 Operating & Maintenance Instructions Download Page 11

11

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

MAINTENANCE

Always ensure the cables & clamps are in good condition and the clamps are 
clean and corrosion free. If damaged they should be replaced. Keep the unit 
clean by wiping with a dry cloth. DO NOT use solvents as a cleaning agent.

Keep the unit at HIGH or FULL CHARGE status at all times.

Always turn the jump-start OFF during storage and store in an upright position, 
away from direct sunlight, moisture or sources of extreme heat or cold.

NEVER attempt any repair unless your are a qualified technician. Your Clarke 
jump-start has been designed to give long and trouble free service. If, 
however, having followed the instructions in this booklet carefully, you 
encounter problems, take the unit to your local Clarke dealer.

CHANGING THE BATTERY

1. Unscrew and remove the self tapping screws securing the back cover. Lift 

off the cover to expose the battery and other components.

2. Lift out the battery from the battery compartment, and detach the heavy 

duty, and other cables, from the battery terminals.

3. Taking great care not to short across the battery terminals, connect the 

RED heavy duty cable, and other cable with red sheath, to the battery 
terminal painted RED, and the black cables to the other battery terminal.

4. Gently slide the new battery into position in its compartment, taking care 

not to damage the printed circuit board.

5. Replace the back cover and secure with the self tapping screws.

CHANGING THE LIGHT BULB

1. Gently squeeze the sides of the lens bezel together, or very carefully use a 

screwdriver to disengage the clips at each side & pull the lens & bezel out.

2. Unscrew and remove the burned out bulb and screw in a replacement.

3. Snap the lens and bezel back into place and replace the back cover.

 

Spare parts are available as follows

Part Number

1

Positive Battery Connection Lead

 HT90001

2

Lamp Bezel 

 HT90003

3

Lamp Lens

 HT90004

4

230 Volt Charger assembly

 HT90006

5

Negative Battery Lead

 HT90002

6

Battery (12V/17AH

 HT90005

Summary of Contents for JS900













Reviews: