Clarke IVP14A Operation & Maintenance Instructions Manual Download Page 11

11

 

DECLARATION OF CONFORMITY 

This is an important document and should be retained. 

 

 

07-0738 IVP14A Sub Pump RV1.doc 

 

Page 1 of 1 

 

We declare that this product complies with the following directives: 

89/336/EEC  

Electromagnetic Compatibility directive, (amended 2004/108/EC). 

2006/95/EC 

Low Voltage Equipment directive (amended by 93/68/EEC). 

98/37/EC Machinery 

Directive 

2002/95/EC 

Restriction of Hazardous substances 

The Following Standards have been applied to the product:  

EN 292-1,  

EN 292-2,  

EN 55014-1:2001,  EN 55014-2:1997,  EN 60555-2/3 

EN 60335-1 

EN 60335-2-41 

The technical documentation required to demonstrate that the products meet the 
requirements of the Low Voltage Equipment directive has been compiled and is available 
for inspection by the relevant enforcement authorities. 

The CE mark was first applied in: 

2007 

 

Product Description:

 

 

Submersible Water Pump 

Model number(s):

 

IVP/14A 

Serial / batch Number: 

 

Current Manufacture.

 

Date of Issue:

 

 

15/002/2007 

 

Signed  

 

 

 

 

 

 

  A.C. A

IKEN 

Senior Manager Clarke International. 

Summary of Contents for IVP14A













Reviews: