Clarke CMFT300QR Operation & Maintenance Instructions Manual Download | Manualshive

Page: 13 / 16

background image

13

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

MAINTENANCE

Remove the plug from the power supply before you carry out any cleaning or
maintenance.

CLEANING

1. Make sure that any ventilation slots are clear.

2. Clean the outside of the tool with a soft cleaning cloth.

3. Do not use any chemicals, harsh abrasives, or solvents when cleaning

plastic parts.

GENERAL MAINTENANCE

• All bearings are sufficiently lubricated for the life of the tool.

• Speak to your Clarke supplier if internal maintenance is necessory.

«
...
11
12
13
14
15
...
»

Summary of Contents for CMFT300QR

















Reviews:

No comments

Related manuals for CMFT300QR

Brand: JVA Pages: 22

Brand: Fagor Pages: 256

Brand: FAR Pages: 44

Brand: FAR Pages: 28

Brand: FAR Pages: 32

Brand: FAR Pages: 24

Brand: FAR Pages: 68

Brand: FAR Pages: 8

Brand: Tanco Pages: 26

Professional GSH65-C5

Brand: P.I.T. Pages: 20

Brand: Gechter Pages: 60

Brand: Chicago Pneumatic Pages: 32

Brand: PowerBox Systems Pages: 30

GC-CG 3,6 Li WT

Brand: EINHELL Pages: 72

TJEP KA 4060 GAS 3G

Brand: Kyocera Pages: 8

Brand: Omega Lift Pages: 36

Brand: Promaker Pages: 24

Brand: H&S Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands