Clarke 6500421 Operation & Maintenance Instructions Manual Download Page 19 | Manualshive

Page: 19 / 24

background image

19

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

be stored in a dry place as if it allowed to become damp, the abrasive
particles will detach from the sheet and will not abrade.

POOR DRIVE

If the sander does not reach full speed or slows down during hard sanding, the
main drive belt may be slipping. Tension the belt by means of the adjsuting
bolts shown on page 10.

ACCESSORIES

Replacement discs and belts are available in packs of 5 from your CLARKE
dealer.

Please quote the part numbers below.

6” Replacement belts (150 x 1219mm)

Part Number

Fine

6502098

Medium

6501164

Coarse

6502103

Replacement 9”discs

Part Number

Fine

6502099

Medium

6501076

Coarse

6502100

«
...
17
18
19
20
21
...
»

Summary of Contents for 6500421

























Reviews:

No comments

Related manuals for 6500421

Brand: RODCRAFT Pages: 9

Brand: Guild Pages: 16

FS-CG-140X140X80

Brand: Argos Pages: 11

Brand: Ewbank Pages: 24

Brand: Evolution Pages: 18

Brand: Kobalt Pages: 32

Brand: Haas Pages: 246

Brand: Skil Pages: 112

Brand: Skil Pages: 104

Brand: Flex Pages: 10

HEAVY DUTY AP 14-2 200E

Brand: Milwaukee Pages: 11

Brand: Grizzly Pages: 1

Brand: Meister Pages: 80

Brand: Pace Technologies Pages: 23

AG700 Intex Giraffe

Brand: Intex Pages: 16

Pro RDP-SPC20 SOLO

Brand: Raider Pages: 98

Brand: Dremel Pages: 35

Brand: Ferm Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands