background image

3

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

SAFETY PRECAUTIONS

WORK ENVIRONMENT

1. Keep the work area clean and tidy.

2. Do not wear loose clothing or jewellery. Tie long hair out of the way.

3. Keep children and visitors away - do not let children handle the wrench.

4. Do not use in damp or wet conditions. Keep the work area well lit. Do not 

use where a risk of fire or explosion is present.

5. Although the wrench may be used outdoors, DO NOT leave it exposed to 

the elements. Avoid direct sunlight, direct heat, rain/moisture etc.

6. ALWAYS keep body and clothing dry. Never work in damp area without 

adequate insulation against electric shock.

7. ALWAYS

 

store this product in a dry, secure place out of reach of children or 

untrained users.

8. ALWAYS

 

keep equipment dry especially the battery & battery charger. 

9. NEVER over-reach. Keep proper footing and balance at all times.

GENERAL USE

1. This product vibrates during use. Vibration may be harmful to your hands or 

arms. Stop using the wrench if discomfort, a tingling feeling or pain occurs 
and seek medical advice before resuming use.

2. ALWAYS use ear defenders for prolonged work.

3. ALWAYS stay alert and use common sense - do not use this product when 

you are tired or under the influence of alcohol or medication.

4. ALWAYS ensure the workpiece is firmly secured leaving both hands free to 

control the wrench.

5. ALWAYS

 

check for any damage or condition that could affect the 

wrench’s operation. Any damaged part should be properly repaired.

6. NEVER force or misuse the wrench. It will do a better and safer job at the 

rate for which it was designed.

7. NEVER use the wrench if it is defective / operating abnormally.

8. NEVER carry the wrench with your finger on the trigger.

9. NEVER abuse the mains cable of the battery charger. Never yank the 

cable to disconnect it from the socket. Keep the cable away from sharp 
edges/hot surfaces.

Summary of Contents for 6487070

















Reviews: