background image

5

AIR COMPRESSOR SAFETY INSTRUCTIONS

1.

ONLY USE WITHIN THE RECOMMENDED OPERATING TEMPERATURE RANGE: 

This compressor should only be used in an ambient temperature of 
b5

O

C and +40

O

C (never at or below freezing temperatures).

2.

NEVER USE AN AIR COMPRESSOR WHICH APPEARS DEFECTIVE OR IS 
OPERATING ABNORMALLY: 

If the compressor operates unusually or makes 

strange noises, switch off immediately and purge the air reservoir. Arrange 
repairs with your nearest dealer.

3.

BREATHING QUALITY AIR: 

This compressor should not be used to supply 

breathing quality air.

4.

SAFETY VALVE: 

Never remove or attempt to adjust the safety valve. The 

maximum pressure is factory set. Keep the safety valve free from paint and 
other accumulations.

5.

AVOID UNINTENTIONAL STARTING: 

Do not move the compressor when it is 

connected to the mains power supply.

6.

BEFORE EACH USE CHECK THE COMPRESSOR AND HOSE FOR DAMAGED 
PARTS: 

Never use the compressor if it has been damaged in any way. Have 

the compressor repaired by a qualified service engineer. Do not use the 
compressor if the On/Off switch does not operate correctly.

7.

KEEP THE MOTOR AIR VENTS CLEAR: 

Keep the motor vents clear and free 

from dust. Wipe regularly to maintain an adequate supply of clean air. 
Avoid using in dusty conditions.

8.

OPERATE THE COMPRESSOR AT THE CORRECT VOLTAGE:

 Make sure that the 

mains supply voltage is the same as the voltage shown on the label.

9.

ALWAYS

 adjust the pressure regulator to the recommended setting for the 

particular spray gun or air tool being used.

10. When using the compressor for painting:

DO NOT 

work in enclosed areas or near naked flames.

Ensure that the area in which you are working has good ventilation.

Protect your nose and mouth with a suitable face mask.

ALWAYS

 check the safety data sheets for substances being sprayed & 

ensure manufacturer’s instructions are followed.

11.

DO NOT USE THIS COMPRESSOR TO INFLATE SMALL, LOW-PRESSURE OBJECTS:

 

Items such as children's toys or footballs can explode if over-inflated.

12.

NEVER STOP THE COMPRESSOR BY REMOVING THE PLUG OR SWITCHING OFF 
AT THE MAINS SUPPLY: 

Always use the On/Off switch on the compressor.

Summary of Contents for 2320875





















Reviews: