background image

13

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

Compressor 
unit runs on 
and off load 
more 
frequently 
than usual.

Large amount of 
condensation in air receiver.

Drain off condensation 
Regularly (Every day 
before use).

Leaks in system

Locate leaks (by means of 
soapy water) and repair.

Compressor 
unit runs ‘on 
load’ when 
no air is being 
used.

Leaks in system

Locate leaks (by means of 
soapy water) and repair.

Compressor’s 
oil 
consumption 
rising.

Too much oil in compressor.

Check oil level 2 or 
3 minutes after stopping.

Leaks around crank case

Contact Clarke Service 
Department

Working temperature of 
compressor too high because 
of insufficient cooling. 

Increase ventilation to air 
compressor.

Cylinder worn.

Contact Clarke Service 
Department

Intake air filter blocked

Clean or replace

Oil in the air 
delivered.

Sump over full

Reduce oil to correct level.

Cylinder worn

Contact Clarke Service 
Department

Intake air filter blocked

Clean / Change air filter.

Oil level rises 
although no 
oil has been 
put in.

Condensation in oil pump.

Compressor over 
dimensioned.

Condensation 
at outlet 
points.

Piping installation incorrect. 

Consult your local dealer

Compressor taking in air 
which is too warm.

Obtain better fresh-air 
supply to compressor.

SYMPTOM

PROBABLE CAUSE

REMEDY

Summary of Contents for 2092500

















Reviews: