Clarion CX501, Service Manual

Page: 7 / 31

-7-
CX501/CX501B/CX501A
051-3730-00 LV5680P Power IC
Pin No. Terminal Function
ILM OUT At CTRL1=M1,M2,H,
OUT=ON 12.0V/300mA
2 ILM_F ILM Feed back
CD OUT
At CTRL2=M,H,
OUT=ON 12.0V/300mA
4 AUDIO_F AUIDO Feed back
5 AUDIO AUDIO OUT At CTRL2=M,H,
ǂǂ
OUT=ON
6 CTRL2 CTRL2(Input) 3 Values input
7 VCC Power
8 CTRL1 CTRL1(Input) 4 Values input
9 GND GND
10
ACC
Accessory detector(input)
Accessory OUT
At ACC
˚
3V, OUT=ON
12 VDD5V VDD5V OUT 5.0V/500mA
SW5V OUT
At CTRL2=M,H,
OUT=ON
ANT OUT At CTRL1=H, OUT=ON
VCC-0.5V/300mA
EXT OUT At CTRL1=M2,H,
OUT=ON
VCC-0.5V/350mA
ILM 1
CD 3
ACC5V
EXT
15
13
ANT
11
SW5V
14
pin 43 : GP50 : I/O : General purpose I/O port with pull down resistor.
pin 44 : GP51 : I/O : General purpose I/O port with pull down resistor.
pin 45 : GP52 : I/O : General purpose I/O port with pull down resistor.
pin 46 : GP53 : I/O : General purpose I/O port with pull down resistor.
pin 47 : GP30 : I/O : General purpose I/O port with pull down resistor.
pin 48 : GP31 : I/O : General purpose I/O port with pull down resistor.
pin 49 : GP32 : I/O : General purpose I/O port with pull down resistor.
pin 50 : GP33 : I/O : General purpose I/O port with pull down resistor.
pin 51 : GP34 : I/O : General purpose I/O port with pull down resistor.
pin 52 : GP35 : I/O : General purpose I/O port with pull down resistor.
pin 53 : GP36 : I/O : General purpose I/O port with pull down resistor.
pin 54 : GP37 : I/O : General purpose I/O port with pull down resistor.
pin 55 : MODE0 : IN : LSI mode set pin 0 This pin must be .
connected to the 0V level.
pin 56 : MODE1 : IN : LSI mode set pin 1 This pin must be connected
to the 0V level.
pin 57 : DVDD : - : Digital system power supply.
pin 58 : DVSS : - : Digital system ground. This pin must be
connected to the 0V level.
pin 59 : RESB : IN : IC reset input ("L"-active).
pin 60 : SIFCK : IN : Host-I/F.
pin 61 : SIFDI : IN : Host-I/F.
pin 62 : SIFDO : IN : Host-I/F.
pin 63 : SIFCE : IN : Host -I/F.
pin 64 : BUSYB : IN : Host -I/F.
pin 65 : GP03 : I/O : General purpose I/O port with pull down resistor.
pin 66 : GP04 : I/O : General purpose I/O port with pull down resistor.
pin 67 : GP05 : I/O : General purpose I/O port with pull down resistor.
pin 68 : GP06 : I/O : General purpose I/O port with pull down resistor.
pin 69 : GP07 : I/O : General purpose I/O port with pull down resistor.
pin 70 : XVDD1 : - : Oscillator power supply.
pin 71 : XIN : IN : 12MHz oscillator connection.
pin 72 : XOUT : O : 12MHz oscillator connection.
pin 73 : XVSS1 : - : Oscillator ground.
This pin must be connected to the 0V level.
pin 74 : UDM : I/O : USB data input/output D ˉ signal connection.
pin 75 : UDP : I/O : USB data input/output D ˇ signal connection.
pin 76 : UVDD : - : USB power supply.
pin 77 : VVDD2 : - : System PLL power supply.
pin 78 : VVSS2 : - : System PLL ground.
This pin must be connected to the 0V level.
pin 79 : AFILT : - : Audio PLL charge pump output.
pin 80 : VVDD3 : - : Audio PLL power supply.
pin 81 : MODE2 : IN : LSI mode set pin 2 .
This pin must be connected to the 0V level.
pin 82 : JTRSTB : IN : JTAG reset input .
pin 83 : JTCK : IN : JTAG clock input .
pin 84 : JTDI : IN : JTAG data input .
pin 85 : JTMS : IN : JTAG mode input.
pin 86 : JTDO : O : JTAG data output.
pin 87 : JTRTCK : O : JTAG return clock output .
pin 88 : DVDD : - : Digital system power supply.
pin 89 : DVSS : - : Digital system ground.
This pin must be connected to the 0V level.
pin 90 : DVDD15 : IN : Capacitor connection pin for internal regulator.
pin 91 : XVSS2 : - : Oscillator ground.
This pin must be connected to the 0V level.
pin 92 : X16OUT : O : 16.9344MHz oscillator connection.
pin 93 : X16IN : IN : 16.9344MHz oscillator connection.
pin 94 : XVDD2 : - : Oscillator power supply.
pin 95 : LRVDD : - : Audio LPF power supply.
pin 96 : LCHO : O : Audio Lch data output.
pin 97 : LRREF : IN : Reference voltage for audio LPF.
pin 98 : RCHO : O : Audio Rch data output.
pin 99 : LRVSS : - : Audio LPF ground.
This pin must be connected to the 0V level.
pin 100 : SLCO : O : Slice Level Control output.
1.Terminal Description
pin 1 : SPK_A_N : O : Speaker output negative (left side).
pin 2 : SPK_A_P : O : Speaker output positive (left side).
pin 3 : SPK_B_N : O : Speaker output negative (right side).
pin 4 : SPK_B_P : O : Speaker output positive (right side).
pin 5
: GND : - : Ground.
pin 6 : MIC_A_P : IN : Microphone input positive (left side).
pin 7 : MIC_A_N : IN : Microphone input negative (left side).
pin 8 : MIC_B_P : IN : Microphone input positive (right side).
pin 9 : MIC_B_N : IN : Microphone input negative (right side).
pin 10 : NC : IN : Not in use.
pin 11 : PCM_IN : IN : Synchronous data input.
pin 12 : PCM_SYNC : - : Synchronous data sync.
pin 13 : PCM_CLK : - : Synchronous data clock.
060-8123-90 GTBM501 Bluetooth System controller
pin 14 : PCM_OUT : O : Synchronous data output.
pin 15 AIO0 I/O Analogue programmable input/output line.
pin 16 : AIO1 : I/O : Analogue programmable input/output line.
pin 17 : PIO12 : I/O : Programmable input/output line.
pin 18 : GND : - : Ground.
pin 19 : POWER : O : +3.3V Supply
pin 20 : USB_DP : I/O : USB data plus with selectable internal
1.5k ಳ pull-up resistor
pin 21 : USB_DN : : USB data minus.
pin 22 : UART_RTS : O : UART request to send active low.
pin 23 : UART_CTS : O : UART clear to send active low.
pin 24 : UART_TX : O : UART data output.
pin 25 : UARTR_RX : IN : UART data input.
pin 26 : RESET : O : Reset If Low.
pin 27 : GND : - : Ground.
pin 28 : PIO4 : I/O : Programmable input/output line.
pin 29 : PIO5 : I/O : Programmable input/output line.
pin 30 : PIO6 : I/O : Programmable input/output line.
pin 31 : PIO7 : I/O : Programmable input/output line.
pin 32 : SPI_MOSI : IN : SPI data input.
pin 33 : SPI_CSB : O : Chip select for SPI, active low.
pin 34 : SPI_CLK : O : SPI clock.
pin 35 : SPI_MISO : O : SPI data output.
pin 36 : PIO10 : I/O : Programmable input/output line.
pin 37 : PIO11 : I/O : Programmable input/output line.
pin 38 : PIO3 : I/O : Programmable input/output line.
pin 39 : PIO2 : I/O : Programmable input/output line.
pin 40 : PIO1 : I/O : Programmable input/output line.
pin 41 : PIO0 : I/O : Programmable input/output line(external RXEN).
pin 42 : PIO8 : I/O : Programmable input/output line
.
pin 43 : PIO9 : I/O : Programmable input/output line.
pin 44 : GND : - : Ground.
pin 45 : AUX_DAC
: O : 8-bit voltage output DAC.
pin 46 : GND : - : Ground.
pin 47 : ANT : IN : RF Interface.
pin 48 : GND : - : Ground.
pin 49 : GND : - : Ground.
pin 50 : VBUS : IN : Lithium ion/polymer battery charger input.
pin 51 : VBATT : O : Lithium ion/polymer battery positive
terminal. Battery charger output and
input to switch-mode regulator.
pin 52 : GND : - : Ground.
pin 53 : MIC_BIAS : O : 2.7V/Programmable Mic Bias Output
.