clage German Pool DBN, User Manual

Page: 10 / 21

S
A
6. Electrical Connection
WARNING: Check that the power supply is switched off prior to electrical
connection!
1. Open the prepared breaking point (S) in the upper part of the appliance by pressing
with a blunt implement (e.g. screwdriver). For surface-mounted connection cable
additional open the breakout at the right side of the bottom part.
2. Slit the grommet of the accessory set to match the cable size. The opening in the
grommet should be slightly smaller than the cross-section of the cable in order to
ensure optimum protection against water. Fit the grommet into the opening. The
protection grommet must be used!
3. Strip the connection cable so that the sheath extends through the grommet into
the appliance. Hold the prepared appliance so that you can route the cable into the
grommet with the other hand.
4. Place the appliance on the wall bracket so that the threaded rod of the wall bracket
fits in the corresponding hole of the appliance and fix it with the knurled nut.
5. Unscrew the fastening screw of the connecting terminal. Displace the connecting
terminal to the upper foot. Affix the connecting terminal again.
6. Strip the individual wires of the connecting cable and plug them in the connecting
terminals according to the wiring diagram. The appliance must be earthed.
7. Place the hood on the appliance and screw in the fastening screw. After that you
can slide on the faceplate from the bottom up to the stop.
Note: To ensure IP25 protection class, please don´t remove the bottom water splash
protection sleeve.
Electrical Connection from Above
WARNING!
WARNING!
SDB
S
STB
Before making the electrical connection, fill the mains and the appliance with water
by carefully opening and closing the hot water tap in order to vent completely.
To ensure a maximum flow, remove any existing aerator from the faucet. Flush the
warm and cold water pipes each at least for one minute.
After every draining (e.g. after work on the plumbing system or following repairs to
the appliance), the heater must be re-vented in this way before starting it up again.
If the water heater cannot be put into operation, the temperature cut-out or the pres-
sure cut-out may have tripped during transport. If necessary, check that the power
supply is switched off and reset the cut-out.
1. Switch on the power supply to the appliance.
2. Open the hot water tap. Check the function of the appliance. The heating element
will be activated after approx. 10 – 30 sec of continuous water flow.
3. Explain the user how the instantaneous water heater works and hand over the
operating instructions.
4. Fill in the guarantee registration card and send it to the German Pool Customer
Service Centre or use the online registration (see also page <2>).
7. Initial Operation
The factory set hot water outlet temperature is 50 °C.
By turning the adjustment potentiometer with the auxiliary tool “S”, this presetting can
be changed between two stops in the range of approx. 30 °C to 60 °C.
The hot water outlet temperature will be increased by clockwise rotation and
decreased by counterclockwise rotation.
Note: The hot water temperature may not exceed 55 °C if the instant water heater is
connected to a shower.
Modification of Factory Preset Outlet Temperature
WARNING!
Electrical Connection From Below
Note: If necessary, the connecting terminal can be displaced to the upper part of the
appliance. If you want to do so, please follow the instructions in the next chapter.
WARNING: Check that the power supply is switched off prior to electrical
connection!
1. Dismantle approximately 6cm off the connecting cable above the wall outlet. With
the smaller opening ahead, slide the water protection sleeve over the connecting
cable so that the sleeve is flush with the wall. This prevents any leaking water from
coming into contact with the electrical leads. It must not become damaged! The
protection sleeve must be used!
2. Strip the cables and plug them in the connecting terminals according to the wiring
diagram. The appliance must be earthed.
3. Pull the protective sleeve over the connecting cables until the sleeve fits perfectly
in the recess of the intermediate panel. Adjust the water splash protection sleeve as
illustrated and fix it with the sleeve fixing (A).
4. Place the hood on the appliance and screw in the fastening screw. After that you
can slide on the faceplate from the bottom to the top.
18 19