manualshive.com logo in svg

CKD WFK2-005, Manual, Page: 17 / 20

Share
Download
CKD WFK2-005 Manual Download Page 17

14

WFK2 

Series

 

When installing piping, align the fluid flow direction 

to the direction marked on the body. Connecting 

the pipe in the wrong direction prevents correct 

measurement of the flow rate.

 

Before installing piping, clean the pipes to remove 

foreign matter, cutting chips, residual testing water, 

etc.

 

Make sure that no force is applied to the resin parts 

when piping.

 

Make sure that the self-weight of the piping is not 

applied to flow rate sensor.

  It may lead to damage or external leakage. We 

recommend that piping be fixed during operation.

 

Make sure that no sealing tape or adhesive enters 

the pipes when connecting the piping.

 

When freezing may occur, take antifreezing 

measures with the devices used, such as draining 

the pipes of water.

 

If there is significant difference between the ambient 

temperature and the fluid temperature, condensation 

occurs, which can enter wiring parts and cause 

operation failure. If condensation should occur, 

ensure that the mounting orientation of the flow rate 

sensor is horizontal and the display is facing upward.

 

When connecting pipes, wrap sealing tape in the 

opposite direction from threads starting 2 mm inside 

from the end of piping threads.

 

If sealing tape protrudes from the pipe threads, it could be 

cut when screwing the bolts in. This could cause the tape to 

enter the valve, causing failures.

 

When using a liquid sealant, make sure it does not adhere 
to resin parts. Otherwise resin parts could be damaged, 

which is dangerous.

Flow direction

 

Use proper torque to tighten the pipes when 

connecting them. 

 

The purpose is to prevent water leakage and screw 

damage.

 

First tighten the screw by hand to ensure that threads are 

not damaged, then use a tool.

 

When mounting piping or fittings to this product, always 

hold the attachment on the mounting side with a tool.

  Holding the body of the product or the attachment on the 

opposite side may lead to damage.

(Recommended values)

Port thread

Tightening torque   N·m

Rc3/8

31 to 33

Rc1/2

41 to 43

Rc3/4

62 to 65

Rc1

83 to 86

Rc1 1/4

94 to 100

Rc1 1/2

104 to 108

Solid/liquid 
sealant

Solid/liquid 
sealant

OK

OK

Summary of Contents for WFK2-005





















Reviews:

No comments