background image

IMPORTANT N

NOTES

This fire is an Inset Live Fuel Effect Gas Fire providing radiant warmth. It is designed to operate on Natural Gas
only.

It is the LAW that all gas appliances and fittings are installed by a competent person (such as a CORGI registered
fitter) and in accordance with the Gas Safety (Installation and Use) Regulations 1998, the relevant British
Standards for Installation, Codes of Practice and in accordance with the Manufacturers’ Instructions. The
installation shall also be carried out  in accordance with the following regulations:

The Building Regulations issued by the Department of the Environment, the Building Standards (Scotland)
(Consolidation) Regulations issued by the Scottish Development Department.

BS 5871 part 2

BS 5440 part 1

BS 1251

BS 6891

BS 6461 part 1

Failure tto ccomplyy w

with tthese rregulations ccould llead tto pproseccution aand ddeem tthe w

warrantyy

invalid.

This  aappliancce  m

must  bbe  iinstalled  iin  aaccccordancce  w

with  tthe  rrules  iin  fforcce  aand  uused  oonlyy  iin  aa

sufficcientlyy vventilated sspacce.

Consult aall iinstrucctions bbefore iinstallation aand uuse oof tthis aappliancce.

This aappliancce iis ffree ffrom aanyy aasbestos m

material. RRefracctories aand ffuelbed aare cconstruccted

from cceramicc ffibre.

1

Secction

1.0
2.0
3.0
4.0
4.1
5.0
6.0
7.0

7.1

8.0

8.1

8.2
8.3

Contentss

Important Notes
Appliance Data
Installation Requirements
Site Requirements
Debris Collection Space
Ventilation
Flue Box
Unpacking the Appliance
Component Checklist
Installation of Appliance
Preparing the Appliance
Preparing the Opening
Gas Supply Routing

Pagge N

No.

1
2
2
3
4
4
4
4
5
5
5
5
6

Secction

8.4
8.5
9.0

9.1

10.0

11.0

11.1

11.2
11.3

12.0

12.1

13.0
14.0
15.0

Contentss

Cable Fixing
Fitting the Burner Tray
Fuel Bed Layout (coal effect models)
Fuel Bed Layout (pebble effect models)
Fitting the Fireframe
Testing and Commissioning
Operating the Appliance
Spark Failure
Setting Pressure
Spillage Monitoring System
Testing for Spillage
Briefing the Customer
Servicing
Troubleshooting Guide

Pagge N

No.

6
7
7
8
8
9
9
9
9
9
9

10
10

11

Note - FFor RRepublicc oof IIreland, rreferencce

sshould bbe m

made tto tthe rrelevant sstandardss

ggoverningg iinsstallation, pparticcularly iin rreggard

to fflue ssizingg aand vventilation. SSee IIS813,

ICP3, IIS3277 aand aany oother rruless iin fforcce.

1.0

Summary of Contents for Afina Multiflue

















Reviews: