background image

30

EasyCall Gateway Telephony System Integrator’s Guide

Trunk Configuration page (continued): version 6.0

Note

The PBX administrator must provide the following call routing information for 

Inbound Calls

 section of the SIP trunk configuration:

Calling Search Space

AAR Calling Search Space

If either of these values is not required, select 

None

.

Setting

Description

Destination Address

The EasyCall Gateway address.

Destination Port

The port of the proxy server. Defaults to 5060 and should not be changed.

Media Termination Point 
Required

We recommend not enabling MTP Required. However, please consult your 
telephony administrator or Cisco representative regarding the requirements for 
your environment. 

SIP Trunk Security 
Profile

Must be Non Secure SIP Trunk Profile - UDP, as entered when “Configuring the 
SIP Trunk Security Profile” on page 27.

Preferred Originating 
Codec

Must be 711ulaw.

DTMF Signaling Method

Most environments will automatically use RFC2833 for this setting when No 
Preference is selected. If that is not the case for your site, select 

RFC2833

 for 

this setting. 

Summary of Contents for EasyCall Gateway 3.0













































Reviews: