background image

 

26 

 

DB9 Interface Connector   

 

 

 

 

DB9 PIN Assignment - 1K 

 

PIN 1: UPS Fault 

PIN 2: AC POWER Failure 

PIN 3: Inverter Power On 

PIN 4: Common GND of Pin 1,2,3,5,8 

PIN 5: UPS Battery Low   

PIN 6: Turn off UPS 

PIN 7: GND of PIN6 

PIN 8: inverter Output 

PIN 9: RS232 TXD 

 

DB9 PIN Assignment – 2K/3K 

 

PIN 2: RS232 RXD 

PIN 3: RS232 TXD 

PIN 5: GND   

The other PINs have no function. 

 

 

 

 

DB9 INTERFACE CONNECTOR

 

27

9. SPECIFICATIONS 

Rated Power   

Capacity 

1KVA / 700W 

2KVA / 1400W 

3KVA / 2100W 

Voltage 

Single phase 220Vac, 160~300Vac at 70~100% load 

140~300Vac at 50~70% load, 118~300Vac at 0~50% load 

Frequency 

50Hz or 60Hz +/- 4Hz 

Input 

Power Factor 

 0.95 

Voltage, Frequency 

Single phase /- 2% (230V or 240V re-settable via 

LCD panel), 50Hz or 60Hz 

Transient Response 

+/- 3% (100% load variation) 

Waveform / Distortion 

Sine wave, THD < 3% at 0-100% linear load 

Output 

Crest Ratio 

3 : 1 

Voltage (longer backup 
time is available upon 
request) 

7Ah / 12V * 3pcs

7Ah / 12V * 8pcs 

Battery 

Charger 

5 hrs to 90% of full capacity after full load discharge 

Transfer Time 

AC fail 0 ms; 2.5ms typical from inverter to bypass and vice versa 

Battery 

Battery low shutdown and Fuse 

Overload 

125~150% 30sec, then switch to bypass and auto 

re-transfer; >150% for 200ms 

Short Circuit 

Current Limited and cut-off and fuse and breaker 

Protection 

EMI/EMC 

EN50091-2 

Mains Failure 

Beeping every 4 seconds 

Battery Low 

Beeping once every second 

Audible Alarm 

Fault, Overload 

Continuously 

LCD 

UPS status, I/P&O/P voltage& frequency, Battery voltage, 

Battery capacity, Loading %, Temperature, History record 

Indicator 

LED 

Normal (green), Warning (yellow), Fault (red) LED 

DB9 Connector 

RS-232 Interface; Power monitoring software (Option) 

Communications

SNMP Intelligent Slot   

Power management from SNMP manager and Web 

browser (Option) 

Network 

Surge Protection 

RJ11 I/O port available for 10 base-T network 

or Fax / Modem 

Temperature 

0-40 degree C; 32-104 degree F 

Relative Humidity 

0-95% non-condensing 

Environment 

Acoustic Noise 

Less than 45dBA (at 1 meter) 

Net Weight (w/o batt.) 

7kgs 

13.5kgs 

14.5kgs 

Net Weight (w/ batt.) 

14kgs 

34kgs 

35kgs 

Physical 

Dimension (WxHxD)mm 

160x220x400 

200x352x450 

※ 

Specifications are subject to change without notice. 

Summary of Contents for CPO-S1000
















Reviews: