Cisco WS-F6K-48-AF Installation Notes Download

Page: 1 / 60

Corporate Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Catalyst 6500 Series Power over Ethernet
Daughter Cards Field-Upgrade Installation Note

This publication describes how to install and remove the following Catalyst 6500 series Power over
Ethernet (PoE) daughter cards. The PoE daughter cards and a brief description are listed in

Table 1

Note

The WS-F6K-VPWR and WS-F6K-VPWR-GE PoE daughter cards are not interchangeable between
Ethernet modules.

Table 1

PoE Daughter Cards

PoE Daughter Card

Description

WS-F6K-VPWR=

Catalyst 6500 series prestandard PoE daughter
card for 10/100 Ethernet modules.

WS-F6K-VPWR-GE=

Catalyst 6500 series prestandard PoE daughter
card for 10/100/1000 Ethernet modules.

WS-F6K-GE48-AF=

Catalyst 6500 series IEEE 802.3af compliant PoE
daughter card for 10/100/1000 Ethernet modules.

WS-F6K-FE48X2-AF=

Catalyst 6500 series IEEE 802.3af compliant PoE
daughter card.

WS-F6K-48-AF=

Catalyst 6500 series IEEE 802.3af compliant PoE
daughter card for 10/100 and 10/100/1000
Ethernet modules.

Summary of Contents for WS-F6K-48-AF





























































Search results

Summary of Contents for WS-F6K-48-AF

Reviews:

Related manuals for WS-F6K-48-AF

Brands by name

Popular brands

Cisco WS-F6K-48-AF, Installation Notes

Search results

Summary of Contents for WS-F6K-48-AF

Reviews:

Related manuals for WS-F6K-48-AF

Brands by name

Popular brands