Cisco WLC 5700 Series Command Reference Manual Download Page 33

Page: 33 / 82

debug platform pm

To enable debugging of the platform-dependent port manager software module, use the

debug platform pm

command in privileged EXEC mode. To disable debugging, use the

form of this command.

Syntax Description

Displays all port manager debug messages.

all

Displays counters for remote procedure call (RPC) debug messages.

counters

Displays error-disabled-related events debug messages.

errdisable

Displays interface-number translation event debug messages.

if-numbers

Displays interface link-detection event debug messages.

link-status

Displays port manager function event debug messages.

platform

Displays port manager vector-related event debug messages.

pm-vectors

(Optional) Displays vector-function details.

detail

Displays VLAN creation and deletion event debug messages.

vlans

Command Default

Debugging is disabled.

Command Modes

Privileged EXEC

Command History

Modification

Release

This command was introduced.

Cisco IOS XE 3.2SE

Usage Guidelines

The

undebug platform pm

command is the same as the

no debug platform pm

command.

When you enable debugging on a stack, it is enabled only on the active controller. To enable debugging on
the standby controller, start a session from the active controller by using the

session switch-number

command

in privileged EXEC mode. Enter the

debug

command at the command-line prompt of the standby controller.

To enable debugging on the standby controller without first starting a session on the active controller, use the

remote command switch-number LINE

command in privileged EXEC mode.

Examples

This example shows how to display debug messages related to the creation and deletion of VLANs:

Controller#

debug platform pm vlans

Layer 2/3 Command Reference, Cisco IOS XE Release 3E (Cisco WLC 5700 Series)

OL-32323-01

Layer 2/3 Commands

debug platform pm

Summary of Contents for WLC 5700 Series



















































































Search results

Summary of Contents for WLC 5700 Series

Reviews:

Related manuals for WLC 5700 Series

Brands by name

Popular brands

Cisco WLC 5700 Series, Command Reference Manual

Search results

Summary of Contents for WLC 5700 Series

Reviews:

Related manuals for WLC 5700 Series

Brands by name

Popular brands