manualshive.com logo in svg

Cisco Webex DX70, Administrator'S Manual

The Cisco Webex DX70 is an innovative video conferencing device designed for seamless collaboration. To navigate its features and maximize its potential, users can easily access the comprehensive User Manual available for free download from our website. Unlock the full potential of Cisco Webex DX70 with our user-friendly manual.

Share
Download
background image

D15362.16 DX70 and DX80 Administrator Guide CE9.13, JUNE 2020.  

www.cisco.com — Copyright © 2020 Cisco Systems, Inc. All rights reserved. 

5

Cisco Webex DX70 and DX80

 Administrator Guide

Products covered in this guide

•  Cisco TelePresence DX70
•  Cisco TelePresence DX80

From Collaboration Software version 8.2 (CE8.2) all DX80 

and DX70 units can run 

CE software

, which is the same 

software that runs on the Cisco TelePresence SX and MX 

Series. 

Note that Cisco DX650 is not, and will not be, supported 

by CE software.

User documentation

This guide provides you with the information required to 

administrate the video conferencing device. 

The guide primarily addresses capabilities and 

configurations of on-premise registered devices (CUCM, 

VCS), but a sub-set of the capabilities and configurations 

also applies to devices that are registered to our cloud 

service (Cisco Webex).

Refer to the 

►

 

User documentation on the Cisco web site

 

appendix for more information about the guides for this 

product.

Documentation on the Cisco web site

Visit the Cisco web site regularly for updated versions of 

the guides: 

►

 

https://www.cisco.com/go/desk-docs

Documentation for cloud registered devices

For more information about devices that are registered to 

the Cisco Webex cloud service, visit: 

►

 

https://help.webex.com

Cisco Project Workplace

Explore the Cisco Project Workplace to find inspiration 

and guidelines when preparing an office or meeting room 

for video conferencing:

►

 

https://www.cisco.com/go/projectworkplace

Software

Download software for the endpoint from the Cisco web 

site: 

►

 

https://software.cisco.com/download/home 

We recommend reading the Software release notes 

(CE9):

►

 

https://www.cisco.com/c/en/us/support/

collaboration-endpoints/desktop-collaboration-

experience-dx600-series/tsd-products-support-

series-home.html

Converting to CE software

Until September 2016 DX80 and DX70 were shipped 

with 

Android based

 

software

. Before converting to 

CE software

, it is important to carefully consider the 

conversion requirements and the functionality changes 

compared to 

Android based software

; otherwise migration 

can leave you with a non-functional deployment that 

requires you to convert back.

Refer to the software release notes, and the 

►

 Upgrade 

the device software

 chapter.

User documentation and software

Introduction

Configuration

Peripherals

Maintenance

Device settings

Appendices

Introduction

Summary of Contents for Webex DX70




























































































































































































































Reviews:

No comments

Related manuals for Webex DX70

Magnavox FW391C Manual preview
FW391C
Brand: Magnavox Pages: 26
DAB ACTIVE DRIVER M/M 1.1 Programming Manual preview
ACTIVE DRIVER M/M 1.1
Brand: DAB Pages: 10
DAB PUMPS ACTIVE DRIVER M/M 1.1 Manual preview
ACTIVE DRIVER M/M 1.1
Brand: DAB PUMPS Pages: 38
Omnia MPX Node Quick Start Installation Manual preview
MPX Node
Brand: Omnia Pages: 8
PASCO SE-8793 Quick Start Manual preview
SE-8793
Brand: PASCO Pages: 2
Magnavox MAS-30037 Specifications preview
MAS-30037
Brand: Magnavox Pages: 1
Trevi SB 8350TV User Manual preview
SB 8350TV
Brand: Trevi Pages: 24
AEG BSS 4804 Instruction Manual preview
BSS 4804
Brand: AEG Pages: 58
AEG BSS 4806 Instruction Manual preview
BSS 4806
Brand: AEG Pages: 66
AEG BSS 4808 Manual preview
BSS 4808
Brand: AEG Pages: 90
Sharp QT-CD210H Serivce Manual preview
QT-CD210H
Brand: Sharp Pages: 36
AMX Axcess Instruction Manual preview
Axcess
Brand: AMX Pages: 144
LG PCRCUDT3 Installation Manual/User Manual preview
PCRCUDT3
Brand: LG Pages: 26
LG PBASE10 Installation Manual preview
PBASE10
Brand: LG Pages: 20
LG V5000 Owner'S Manual preview
V5000
Brand: LG Pages: 70
LG PCRCUDT2 User Manual preview
PCRCUDT2
Brand: LG Pages: 50
LG RVF1000 Owner'S Manual preview
RVF1000
Brand: LG Pages: 56
LG V-NET PQCPC22A0 Installation & User Manual preview
V-NET PQCPC22A0
Brand: LG Pages: 125

Brands by name

Popular brands

Load more brands