Cisco WCM300 - Channel Bonded Cable Modem Implementation Manual Download Page 63

Page: 63 / 88

5-3

Cisco Cable Wideband Solution Design and Implementation Guide, Release 1.0

OL-10705-02

Chapter 5 Monitoring and Troubleshooting Wideband Components

Monitoring Wideband Components

Monitoring Wideband SPAs

The following commands are useful for monitoring a Cisco Wideband SPA:

•

show hw-module bay oir

•

show diag

•

show controllers modular-cable

show hw-module bay oir

To verify that the Wideband SPA is powered on, use the

show hw-module bay oir

command. If the

Operational Status is “ok”, the Wideband SPA is powered on and operational.

Router#

show hw-module bay 1/0/0 oir

Module Model Operational Status

------------- -------------------- ------------------------

bay 1/0/0 SPA-24XDS-SFP

show hw-module bay oir

displays “admin down” in the Operational Status field, the Wideband SPA

has been administratively disabled.

Router#

show hw-module bay 1/0/0 oir

Module Model Operational Status

------------- -------------------- ------------------------

bay 1/0/0 SPA-24XDS-SFP

admin down

show diag

To display hardware and diagnostic information for a Wideband SPA, use the

show diag

command.

Router#

show diag 1/0/0

Slot/Subslot/Port 1/0/0:

24rfchannel-spa-1 card, 1 port + 1 redundant port

Card is half slot size

Card is analyzed

Card detected 16:47:55 ago

Card uptime: Not Supported

Card idle time: Not Supported

Voltage status: 3.3V (+3.291) NOMINAL 2.5V (+2.495) NOMINAL

1.2V (+1.201) NOMINAL 1.8V (+1.811) FIXED

EEPROM contents, slot 1/0/0:

Hardware Revision : 1.0

Boot Timeout : 500

PCB Serial Number : CSJ09379726

Part Number : 73-9597-03

Part Number Revision : 05

Fab Version : 03

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Deviation Number : 0

Product (FRU) Number : SPA-24XDS-SFP

Version Identifier (VID) : V01

Top Assy. Part Number : 68-2562-03

Board Revision : 05

Summary of Contents for WCM300 - Channel Bonded Cable Modem

























































































Search results

Summary of Contents for WCM300 - Channel Bonded Cable Modem

Reviews:

Related manuals for WCM300 - Channel Bonded Cable Modem

Brands by name

Popular brands

Cisco WCM300 - Channel Bonded Cable Modem, Implementation Manual

Search results

Summary of Contents for WCM300 - Channel Bonded Cable Modem

Reviews:

Related manuals for WCM300 - Channel Bonded Cable Modem

Brands by name

Popular brands