manualshive.com logo in svg

Cisco UCS C200, Installation And Service Manual

Share
Download
Cisco UCS C200 Installation And Service Manual Download Page 82

   

3-42

Cisco UCS C200 Server Installation and Service Guide

OL-20732-02

Chapter 3      Maintaining the Server

  Installing or Replacing Components

b.

Place the new BBU over the BBU bracket on the fan tray and align the three screw-holes in the BBU 
with the three preinstalled standoffs on the bracket.

c.

Replace the three securing screws that hold the BBU to the BBU bracket.

Step 3

If this is a first-time installation of the BBU rather than a replacement, install the cable from the BBU 
to the LSI card.

Connect the cable from the BBU to the socket on the adapter.

Note

Be careful to align the arrow-mark on the cable connector with the arrow-mark on the socket to avoid 
damaging the connector pins.

Figure 3-24

Removing and Replacing an LSIiBBU06 BBU

1

BBU bracket on fan tray

3

BBU (connector J2 is on the underside)

2

Securing screws (three)

1

2

3

Summary of Contents for UCS C200













































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands